IEI Technology HTB-200-C236 User Manual Download Page 17

Page: 17 / 113

HTB-200-C236 Embedded System

Page 5

1.7 Technical Specifications

The specifications for the Intel based embedded systems are listed below.

HTB-200-C236

CPU

Intel® Xeon

E3-1268L v5 (2.4 GHz, quad-core, 35W TDP)

Intel® Core™ i5-7500T (2.7 GHz, quad-core, 35W TDP)

Chipset

Intel

C236

System Memory

2 x 260-pin 1600/2133 MHz dual-channel DDR4 SO-DIMM

ECC/non-ECC unbuffered memory slot (system max. 64 GB)

Preinstalled two 16 GB / 8 GB DDR4 SDRAM SO-DIMM

Thermal Solution

Smart fan

Ethernet

LAN1: Intel

I219-LM PHY with Intel® AMT 11.0 support

LAN2: Intel

I211-AT PCIe controller

Display

1 x HDMI output port (by iDP signal)

Serial Port

1 x RS-232/422/485 (DB-9)

USB

2 x USB 2.0 ports

2 x USB 3.2 Gen 1 (5Gb/s) ports

Storage

1 x 2.5" SATA 6Gb/s HDD/SSD bay

Expansion

1 x PCIe 3.0 x16 slot

1 x PCIe 3.0 x4 slot

1 x Half-size PCIe Mini card slot supports mSATA and USB 2.0

Chassis Construction

Metal housing (SECC)

Power Requirement

19 V DC

Power Supply

180 W power adapter

100V ~ 240V AC input ,19V DC output

Summary of Contents for HTB-200-C236


















































































































Search results

Summary of Contents for HTB-200-C236

Reviews:

Related manuals for HTB-200-C236

Brands by name

Popular brands

IEI Technology HTB-200-C236, User Manual

Search results

Summary of Contents for HTB-200-C236

Reviews:

Related manuals for HTB-200-C236

Brands by name

Popular brands