IEI Technology eKINO-BT User Manual Download

Page: 64 / 157

eKINO-BT Mini-ITX SBC

Page 50

3.3.1 9 V ~ 26 V DC In Connector

CN Label:

SPWR_IN1

CN Type:

4-pin mini-DIN

CN Location:

CN Pinouts:

The power connector connects to the 9 V ~ 26 V DC power adapter.

Pin

Description

Pin

Description

Power (9 V ~ 26 V)

GND

Power (9 V ~ 26 V)

GND

Table 3-28: 9 V ~ 26 V DC In Connector Pinouts

Figure 3-34: 9 V ~ 26 V DC In Connector

3.3.2 Audio Jacks

CN Label:

AUDIO1

CN Type:

Audio jack

CN Location:

See

Figure 3-33

The audio jacks connect to external audio devices.

Line Out port (Lime):

Connects to a headphone or a speaker. With

multi-channel configurations, this port can also connect to front speakers.

Microphone (Pink):

Connects a microphone.

Figure 3-35: Audio Jacks

Summary of Contents for eKINO-BT






























































































































































Search results

Summary of Contents for eKINO-BT

Reviews:

Related manuals for eKINO-BT

Brands by name

Popular brands

IEI Technology eKINO-BT, User Manual

Search results

Summary of Contents for eKINO-BT

Reviews:

Related manuals for eKINO-BT

Brands by name

Popular brands