IEI Technology eKINO-BT User Manual Download

Page: 129 / 157

eKINO-BT Mini-ITX SBC

Page 115

6.1 Available Software Drivers

NOTE:

The content of the CD may vary throughout the life cycle of the product

and is subject to change without prior notice. Visit the IEI website or

contact technical support for the latest updates.

The following drivers can be installed on the system:

Chipset

Graphics

LAN

Audio

Installation instructions are given below.

6.2 Software Installation

All the drivers for the eKINO-BT are on the CD that came with the system. To install the

drivers, please follow the steps below.

Step 1:

Insert the CD into a CD drive connected to the system.

NOTE:

If the installation program doesn't start automatically:

Click "Start->Computer->CD Drive->Autorun.exe"

Step 2:

The driver main menu appears (

Figure 6-1

Step 3:

Click

eKINO-BT

Summary of Contents for eKINO-BT






























































































































































Search results

Summary of Contents for eKINO-BT

Reviews:

Related manuals for eKINO-BT

Brands by name

Popular brands

IEI Technology eKINO-BT, User Manual

Search results

Summary of Contents for eKINO-BT

Reviews:

Related manuals for eKINO-BT

Brands by name

Popular brands