manualshive.com logo in svg

IEI Technology DM-F17A/PC-R31, User Manual, Page: 24 / 88

Share
Download
IEI Technology DM-F17A/PC-R31 User Manual Download Page 24

 

 

DM-F  S e rie s   Mo n ito r

 

P a g e   15 

2.1

 

Un pa c kin g  P ro c e d u re  

To unpack the DM-F series LCD monitor, follow the steps below: 

  WARNING: 

The front side LCD  screen has a protective plastic cover stuck to the 

screen. Only remove the plastic cover after the DM-F series LCD monitor 

has been properly installed. This ensures the screen is protected during the 

installation process. 

S te p  1:

 

Use box cutters, a knife or a sharp pair of scissors that seals the top side of the 

external (second) box. 

S te p  2:

 

Open the external (second) box. 

S te p  3:

 

Use box cutters, a knife or a sharp pair of scissors that seals the top side of the 

internal (first) box. 

S te p  4:

 

Lift the monitor out of the boxes. 

S te p  5:

 

Remove both polystyrene ends, one from each side. 

S te p  6:

 

Pull the plastic cover off the DM-F series LCD monitor. 

S te p  7:

 

Make sure all the components listed in the packing list are present. 

S te p  0:

 

Summary of Contents for DM-F17A/PC-R31

























































































Reviews:

No comments