IEI Technology AFL2-EM-RFID-KIT User Manual Download Page 17 | Manualshive

Page: 17 / 41

background image

AFL2-EM-RFID-KIT01

P a g e 10

3.1

An ti-s ta tic P re c a u tio n s

WARNING

!

Static electricity can destroy certain electronics. Make sure to follow the

ESD precautions to prevent damage to the product, and injury to the

user.

Electrostatic discharge (ESD) can cause serious damage to electronic components,

including the AFL2-EM-RFID-KIT01-R10. Dry climates are especially susceptible to ESD.

It is therefore critical that whenever the AFL2-EM-RFID-KIT01-R10 or any other electrical

component is handled, the following anti-static precautions are strictly adhered to.



Wear an anti-static wristband

: Wearing a simple anti-static wristband can

help to prevent ESD from damaging the board.



Self-grounding

: Touch any grounded conducting material before handling

the board. During the time the board is handled, frequently touch any

conducting materials that are connected to the ground.



Use an anti-static pad

: When configuring the AFL2-EM-RFID-KIT01-R10,

place it on an antic-static pad. This reduces the possibility of ESD damaging

the AFL2-EM-RFID-KIT01-R10.

3.2

P a c kin g Lis t

NOTE:

If any of the components listed in the checklist below are missing, do not

proceed with the installation. Contact the IEI reseller or vendor the

AFL2-EM-RFID-KIT01-R10 was purchased from or contact an IEI sales

representative directly by sending an email t The AFL2-EM-RFID-KIT01-R10 is shipped with the following components:

«
...
15
16
17
18
19
...
»

Summary of Contents for AFL2-EM-RFID-KIT










































Reviews:

No comments

Related manuals for AFL2-EM-RFID-KIT

Brand: Zebex Pages: 75

Brand: Zebex Pages: 72

Brand: Magtek Pages: 18

Brand: TSC Pages: 78

Brand: Salto Pages: 6

Brand: Intermec Pages: 3

Brand: HID Pages: 2

Monarch Pathfinder Ultra Platinum 6039

Brand: Avery Dennison Pages: 12

Brand: Billow Pages: 98

2126800 - Media Reader 7500

Brand: Adaptec Pages: 20

Brand: Iseo Pages: 2

Brand: PlusQuip Pages: 57

Brand: GPRINTER Pages: 85

Brand: Y-E Data Pages: 27

Brand: ZKTeco Pages: 40

Brand: GIGA-TMS Pages: 27

Brand: GE Security Pages: 18

Brand: 2connect Pages: 63

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands