IEI Technology AFL-15A-N270 User Manual Download Page 77

Page: 77 / 158

AFOLUX AFL-15A-N270 Panel PC

Page 77

6.3.2.1 IDE Master, IDE Slave

Use the

IDE Master

and

IDE Slave

configuration menu to view both primary and

secondary IDE device details and configure the IDE devices connected to the system.

BIOS Menu 5: IDE Master and IDE Slave Configuration

Auto-Detected Drive Parameters

The “grayed-out” items in the left frame are IDE disk drive parameters automatically

detected from the firmware of the selected IDE disk drive. The drive parameters are listed

as follows:

Device

: Lists the device type (e.g. hard disk, CD-ROM etc.)

Type

: Indicates the type of devices a user can manually select

Vendor

: Lists the device manufacturer

Size

: List the storage capacity of the device.

LBA Mode

: Indicates whether the LBA (Logical Block Addressing) is a

method of addressing data on a disk drive is supported or not.

Summary of Contents for AFL-15A-N270































































































































































Search results

Summary of Contents for AFL-15A-N270

Reviews:

Related manuals for AFL-15A-N270

Brands by name

Popular brands

IEI Technology AFL-15A-N270, User Manual

Search results

Summary of Contents for AFL-15A-N270

Reviews:

Related manuals for AFL-15A-N270

Brands by name

Popular brands