IEI Technology AFL-15A-N270 User Manual Download Page 61

Page: 61 / 158

AFOLUX AFL-15A-N270 Panel PC

Page 61

4.11.3 USB Device Connection

There are four external USB 2.0 connectors. All connectors are perpendicular to the

AFL-15A-N270 Series. To connect a USB 2.0 or USB 1.1 device, please follow the

instructions below.

Step 1:

Located the USB connectors

. The locations of the USB connectors are shown

Chapter 2

Step 2:

Align the connectors.

Align the USB device connector with one of the

connectors on the bottom panel. See

Figure 4-21

Figure 4-21: USB Device Connection

Step 3:

Insert the device connector.

Once aligned, gently insert the USB device

connector into the onboard connector.

Step 0:

Summary of Contents for AFL-15A-N270































































































































































Search results

Summary of Contents for AFL-15A-N270

Reviews:

Related manuals for AFL-15A-N270

Brands by name

Popular brands

IEI Technology AFL-15A-N270, User Manual

Search results

Summary of Contents for AFL-15A-N270

Reviews:

Related manuals for AFL-15A-N270

Brands by name

Popular brands