IEI Technology AFL-15A-N270 User Manual Download Page 58

Page: 58 / 158

AFOLUX AFL-15A-N270 Panel PC

Page 58

4.10.4 Cabinet and Rack Installation

The AFL-15A-N270 series flat panel PC can be installed into a cabinet or rack. The

installation procedures are similar to the panel mounting installation. To do this, please

follow the steps below:

NOTE:

When purchasing the cabinet/rack installation bracket, make sure it is

compatible with both the AFL-15A-N270 series flat panel PC and the

rack/cabinet into which the AFL-15A-N270 series is installed.

Step 1:

Slide the rear chassis of the AFL-15A-N270 series flat panel PC through the

rack/cabinet bracket until the aluminum frame is flush against the front of the

bracket (

Figure 4-18

Figure 4-18: The Rack/Cabinet Bracket

Step 2:

Follow the

Step 4 ~ Step 7

Section 4.10.2

to mount the AFL-15A-N270 into a

cabinet or rack.

Summary of Contents for AFL-15A-N270































































































































































Search results

Summary of Contents for AFL-15A-N270

Reviews:

Related manuals for AFL-15A-N270

Brands by name

Popular brands

IEI Technology AFL-15A-N270, User Manual

Search results

Summary of Contents for AFL-15A-N270

Reviews:

Related manuals for AFL-15A-N270

Brands by name

Popular brands