Instruction Manual
Innovative DisplayWorks
RCM-2
2
3
1. Cabinet
2. Hinge Cover (6)
3. Damping Box Left Upper
4. Damping Box Left Bottom
5. Damping Left
6. Coolant Box (30)
7. Damping Box Right Upper
8. Damping Right
9. Damping Box Right Bottom
10. Door Gasket
11. Lid
12. Handle
13. Rim
14. Basket
15. Cooling Inner
16. Baffle of Inner Fan
17. Inner Fan Supporter
PARTS AND IDENTIFICATION
充
电
器
蓄
电
池
18. Evaporator Fan
19. Castor (2)
20. Caster Locking (2)
21. Retaining Clip of Line
22. Compressor Accessories
23. Compressor
24. Front Bottom Baffle
25. Compressor Base
26. Assembly
27. Dryer Filter
28. Drip Pan Assembly
29. Ground Wire - 1
30. Ground Wire - 2
31. Compressor Connection Wire
32. Thermostat Connection Wire
33. Power Cord
34. Bottom Front Graphic Strip
35. Corner Graphic Strips (4)
36. Top Magnet Strips Front/
Back (2)
37. Top Magnet Strips Sides (2)
38. Bottom Side Graphic Strips
(2)
39. Bottom Back Graphic Strip
40. Compressor Room Cover
41. Cover Supporter (2)
42. Power Cord Holder (2)
43. Battery Box
44. Rail Supporter (2)
45. Wire Retaining Clip (4)
46. Fixing Plate
47. Thermostat
48. Recharger
49. Battery
SAFETY INSTRUCTIONS
When using this appliance, always follow the basic safety precautions:
1. Read the entire Userʼs Manual before operating this appliance.
2. Use this appliance only for its intended purpose as described in this Userʼs Manual.
3. This cooler must be properly installed in accordance with the installation instructions before being used. See grounding
instructions.
4. IDW requires that a dedicated circuit be used for the unit. Failure to do so voids warranty.
5. Never unplug your cooler by pulling on the power cord. Always grasp the plug fi rmly and pull it straight out from the
outlet.
6. Unplug your cooler before cleaning or making any repairs.
Note: If for any reason this product requires service, we strongly recommend that a certifi ed technician perform the service.
7. When disconnecting the power source, wait at least 5 minutes to reconnect the power to avoid damage to the compressor
and the cooling system.
8. Immediately repair or replace all electrical cords that have become frayed or otherwise damaged. Do not use a cord that
shows cracks or abrasion damage along its length, the plug or the connector end.
9. Do not operate or store your cooler near or around explosive fumes, gasoline or other fl ammable vapors and liquids.
10. Do not use fl ammable liquids to clean unit.
11. Setting the temperature control to the 0 position does not remove power to the light circuit, perimeter heaters, or
evaporator fans.
12. Do not adjust the temperature control. The temperature control is factory set between levels 4 and 5 for maximum
performance.
IMPORTANT!
Please Save These Instructions
For Proper Disposal of the Refrigerator!
PRE-CAUTION, NON-OPERATING COOLERS SHOULD HAVE:
1. Door removed
2. Shelves kept in place in order to prevent any small child from climbing inside cooler
FOR PROPER DISPOSAL OF COOLER:
Distributors / retailers need to contact a qualifi ed service technician:
1. To recover all refrigerant from the cooler
2. To remove the compressor or remove the oil from the compressor
Then the distributor / retailer can contact their local metal recycling center to pick up the remaining cabinet, shelves, etc.
By law, disposal of hazardous wastes may be subject to fi nes and imprisonment under the provisions of the environmental
regulations. For more information please visit: http://www.epa.gov/osw/hazard/index.htm
