background image

 
 
                                                                                                                 

   

 

                                                                          9                                                     

11. Warranty Policy and Limitation of Liability 

 

IDTECK warrants this product against defects in material and workmanship for  the period specified 
below from the date of purchase under normal customer use. This Warranty doesn’t apply: 1) to any 
product  which  has  been  dismantled  without  authorization  of  IDTECK  or/and  has  a  damaged  or 
detached QC label on its back side; 2) to any losses, defects, or damages caused by improper testing, 
operation, installation, maintenance, modification, alteration, or adjustment; 3) to any product with a 
damaged or faded serial number on it; or 4) to any losses, defects, or damages caused by lightning or 
other electrical discharge, natural disaster, misuse, accident or neglect. 
 
This Limited Warranty is in lieu of all other warranties, obligations, or liabilities on the part of IDTECK, 
and  IDTECK  DISCLAIMS  ANY  AND  ALL  WARRANTY,  WHETHER  EXPRESS  OR  IMPLIED,  OF 
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.IDTECK does not, and cannot, 
know who is present, what property is located, where this product will be used; it would be extremely 
difficult to determine the actual damages that may result from a failure of the product to perform as 
anticipated; and the low price of this product is based upon the nature of the product provided and the 
limited  liability  that  IDTECK  assumes.  IDTECK  IS  NOT  RESPONSIBLE  FOR  ANY  PERSONAL 
INJURY, PROPERTY DAMAGE OR LOSS, DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL 
DAMAGES,  OR  OTHER  LOSS,  AND  IDTECK’S  MAXIMUM  LIABILITY SHALL NOT  IN  ANY  CASE 
EXCEED THE PURCHASE PRICE OF THE PRODUCT.   
 

To  obtain  repair  or  replacement  under  the  terms  of  this  warranty,  visit  IDTECK’s  Website 
(http://www.idteck.com) and place an online RMA request.

 After an RMA code is issued, return the 

product along with the authorization RMA code. 
 

>> Warranty Period

 

 

Product Category 

Warranty 

Period 

RF CARD (Active type) 

1 year 

RF READER / FINGERPRINT READER 

3 years 

STANDALONE CONTROLLER 

CONTROL PANEL 

FINGERPRINT CONTROLLER 

MOLDED RF READER 

(RF10, RF20, RF30, RF TINY, IP10, IP20, IP30, SR10E, SR10UE, SR10SE, SR10RWE, 

SR10BE) 

Lifetime 

RF CARD (Passive type) 

(IDC80, IDC170, IDK50, IMC125, LXK50, IPC80, IPC170, IPK50, ISC80, ISC80S, ISK50, 

IMC135, IHC80, IP100, IP200) 

Summary of Contents for iPASS IP30













Reviews: