IDTECK iMDC-MAIN User Manual Download Page 7

Page: 7 / 79

Safety Information

p.1

CAUTION

: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER

(OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIE

D SERVICE PERSONNEL.

This symbol indicates that dangerous voltage consisting a risk of electric shock is pres

ent within this unit.

This exclamation point symbol is intended to alert the user to the presence of importa

nt operating and maintenance (servicing) instructions in the literature accompanying the ap

pliance.

WARNING

To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.

WARNING

Be sure to use only the standard adapter that is specified in the specification sheet. Usin

g any other adapter could cause fire, electrical shock, or damage to the product.

Incorrectly connecting the power supply or replacing battery may cause explosion, fire,

electric shock, or damage to the product.

Summary of Contents for iMDC-MAIN
















































































Search results

Summary of Contents for iMDC-MAIN

Reviews:

Related manuals for iMDC-MAIN

Brands by name

Popular brands

IDTECK iMDC-MAIN, User Manual

Search results

Summary of Contents for iMDC-MAIN

Reviews:

Related manuals for iMDC-MAIN

Brands by name

Popular brands