IDT Tsi578 User Manual Download | Manualshive

Page: 489 / 527

background image

489

Tsi578 User Manual

June 6, 2016

Integrated Device Technology

www.idt.com

B. Clocking

This appendix describes device behavior outside the

RapidIO Interconnect Specification (Revision 1.3)

recommended operating line rates and clock frequencies.

The following topics are discussed:

•

“Line Rate Support” on page 489

•

“P_CLK Programming” on page 493

B.1

Line Rate Support

The Tsi578 supports all of the

RapidIO Interconnect Specification (Revision 1.3)

specified line rates of

1.25, 2.50, and 3.125 Gbaud. The device also supports line rates that are outside of the RapidIO
specification. The ability to support multiple line rates gives the Tsi578 flexibility in both application
support and power consumption.

shows the supported line rates for the Tsi578. The Serial Port Select pin, SP_IO_SPEED[1,0]

must be set to the values shown in

to achieve the documented line rates.

Table 53: Tsi578 Supported Line Rates

a

S_CLK_p/n (MHz)

Baud Rate (Gbaud)

SP_IO_SPEED[1,0] Bit

Settings

Register Settings

153.60

1.2288

CPRI Line Rate

0,0

-

153.60

1.536

OBSAI Line Rate

0,1

-

153.60

2.4576

CPRI Line Rate

0,1

-

153.60

3.0720

CPRI Line Rate

1,0

-

156.25

1.2500

Standard RapidIO Line Rate

0,0

-

156.25

2.5000

Standard RapidIO Line Rate

0,1

-

156.25

3.1250

Standard RapidIO Line Rate

1,0

-

«
...
487
488
489
490
491
...
»

Summary of Contents for Tsi578
















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Tsi578

DMS-1250 Series

Brand: D-Link Pages: 38

Brand: BERNSTEIN Pages: 3

HYGRASREG KW Series

Brand: S+S Regeltechnik Pages: 16

Brand: AsGa Pages: 23

ServSwitch KV1510A

Brand: Black Box Pages: 16

Brand: Accton Technology Pages: 523

Brand: SICK Pages: 19

Brand: Black Box Pages: 2

Brand: DSPPA Pages: 31

IDS-105FE Series

Brand: Perle Pages: 2

COMMANDE MURALE RTS

Brand: SOMFY Pages: 2

Brand: Kramer Pages: 33

Brand: Whelen Engineering Company Pages: 5

ScatterBox POE308

Brand: System Q Pages: 2

Brand: CTC Union Pages: 14

5-Port Gigabit Switch 1000 Mbps

Brand: Hama Pages: 2

Brand: Tvone Pages: 11

Brand: Lindy Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands