IDT Tsi578 User Manual Download | Manualshive

Page: 456 / 527

background image

13. I2C Registers > Register Descriptions

456

Tsi578 User Manual

June 6, 2016

Integrated Device Technology

www.idt.com

13.2.20

Externally Visible I

2

C Enable Register

Any bit set in this register will enable the equivalent bit in the

“Externally Visible I

C Status Register”

to set the ALERT_FLAG. These enables do not affect whether events are set in the global status
register, only whether the asserted events are allowed to set the ALERT_FLAG when changing from 0
to 1. If an event is already asserted in the status when the related enable is changed from 0 to 1, this is
equivalent to the event asserting, and the ALERT_FLAG will be set.

This register is R/W from either the register bus or from the I

2

C bus through the slave interface. If the

register is written by both at the same time, the register bus interface will take precedence.

This register corresponds to the I

2

C peripheral addresses 0x84 through 0x87.

Register name: EXI2C_STAT_ENABLE

Reset value: 0xFFFF_FFFF

Register offset: 0x1D284

Bits

0

1

2

3

4

5

6

7

00:07

RESET

SW_

STAT2

SW_

STAT1

SW_

STAT0

OMBW

IMBR

I2C

TEA

08:15

RCS

MCS

Reserved

LOGICAL

MC_LAT

MCE

16:23

PORT15

PORT14

PORT13

PORT12

PORT11

PORT10

PORT9

PORT8

24:31

PORT7

PORT6

PORT5

PORT4

PORT3

PORT2

PORT1

PORT0

Bits

Name

Description

Type

Reset

Value

0

RESET

Enable RESET Alert Response

0 = Status asserted will not enable setting ALERT_FLAG

1 = Status asserted will enable setting ALERT_FLAG

R/W

1

1

SW_STAT2

Enable SW_STAT2 Alert Response

0 = Status asserted will not enable setting ALERT_FLAG

1 = Status asserted will enable setting ALERT_FLAG

R/W

1

2

SW_STAT1

Enable SW_STAT1 Alert Response

0 = Status asserted will not enable setting ALERT_FLAG

1 = Status asserted will enable setting ALERT_FLAG

R/W

1

3

SW_STAT0

Enable SW_STAT0 Alert Response

0 = Status asserted will not enable setting ALERT_FLAG

1 = Status asserted will enable setting ALERT_FLAG

R/W

1

4

OMBW

Enable Outgoing Mailbox Written

0 = Status asserted will not enable setting ALERT_FLAG

1 = Status asserted will enable setting ALERT_FLAG

R/W

1

«
...
454
455
456
457
458
...
»

Summary of Contents for Tsi578
















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Tsi578

Brand: BABBITT Pages: 14

Brand: BABBITT Pages: 10

Brand: Eaton Pages: 12

Brand: United Electric Controls Pages: 6

Brand: I-Tech Pages: 27

Brand: TRENDnet Pages: 11

Brand: Cardin Elettronica Pages: 2

Brand: SignaMax Pages: 2

Brand: TRENDnet Pages: 16

INTEGRAL Series

Brand: DAS AUDIO Pages: 45

VIGILANT VTS0400

Brand: RONK Pages: 32

Brand: WilTec Pages: 7

Brand: Atlona Pages: 13

Brand: Gefen Pages: 12

Brand: UHPPOTE Pages: 10

Emulation Pod M306V2T-RPD-E

Brand: Renesas Pages: 74

Sure-Wave CM-330/N

Brand: CAMDEN Pages: 4

CyberSWITCH CSX150

Brand: Cabletron Systems Pages: 620

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands