IDT Tsi578 User Manual Download | Manualshive

Page: 357 / 527

background image

12. Serial RapidIO Registers > IDT-Specific Performance Registers

357

Tsi578 User Manual

June 6, 2016

Integrated Device Technology

www.idt.com

12.9.14

RapidIO Port x Receiver Input Queue Congestion Status Register

This register is used to monitor data congestion in the input buffer.

New packets accumulate in the input buffers, destined for the switching fabric. When the number of
buffers in use equals or exceeds the threshold set in DEPTH field of the

“RapidIO Port x Receiver

Input Queue Depth Threshold Register”

, the CONG_CTR field in SPx_R_Q_STATUS is incremented.

The CONG_CTR counter value is writable for testing purposes. This counter stops counting when it
reaches its maximum value. Writing 1 into the INB_DEPTH (see

“RapidIO Port x Interrupt Status

Register” on page 326

) interrupt status bit causes this counter to be reset to 0. The CONG_CTR is

enabled, when CONG_THRESH value is configured to a value other than 0. The CONG_CTR value is
decremented by 1 if it is not read within the Error Rate Bias frequency as specified by the ERR_RB
field in the

“RapidIO Port x Error Rate CSR” on page 304

.

If the CONG_CTR equals or exceeds the threshold CONG_THRESH, the maskable INB_DEPTH
interrupt is generated.

Register name: SP{0..15}_RX_Q_STATUS

Reset value: 0x0000_0000

Register offset: 13094, 13194, 13294, 13394, 13494,

13594, 13694, 13794, 13894, 13994, 13A94,

13B94, 13C94, 13D94, 13E94, 13F94

Bits

0

1

2

3

4

5

6

7

00:7

CONG_CTR

8:15

CONG_CTR

16:23

CONG_THRESH

24:31

CONG_THRESH

Bits

Name

Description

Type

Reset

Value

0:15

CONG_CTR

Input Queue Depth Count

The number of times that the input queue meets or exceeds the
threshold DEPTH field of the

“RapidIO Port x Receiver Input Queue

Depth Threshold Register” on page 355

.

The count is incremented

by 1 when a packet is received. This counter counts up to
0xFFFFand remains at 0xFFFF until reset.

The counter is reset when 1 is written to the INB_DEPTH status bit
(see

“RapidIO Port x Interrupt Status Register” on page 326

). The

counter is enabled if CONG_THRES is set to a value other than 0.
The CONG_CTR value is decremented by 1 if it is not read within the
Error Rate Bias frequency as specified by the ERR_RB field in the

“RapidIO Port x Error Rate CSR” on page 304

R/W

0x0000

«
...
355
356
357
358
359
...
»

Summary of Contents for Tsi578
















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Tsi578

Brand: CALIENT Pages: 22

Brand: Daxten Pages: 2

Brand: Fantech Pages: 4

TotalStorage 3534-F08

Brand: IBM Pages: 105

RedBooks SAN24B-5

Brand: IBM Pages: 11

RedBooks SAN24B-5

Brand: IBM Pages: 2

Brand: IBM Pages: 123

8265 Nways ATM Switch

Brand: IBM Pages: 192

Brand: Communica Pages: 5

Brand: rako Pages: 4

Brand: DAITEM Pages: 37

Brand: Siqura Pages: 2

Brand: Intermatic Pages: 1

Brand: Hall Technologies Pages: 35

Brand: Edge-Core Pages: 12

Brand: Samson Pages: 64

Brand: NTI Pages: 69

Brand: hager Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands