manualshive.com logo in svg

IDT Tsi578, User Manual

The IDT Tsi578 is a high-performance networking switch, and to help you make the most out of its features, we provide a comprehensive User Manual. This manual is available for free download from our website, ensuring effortless access to valuable product information and instructions for optimal usage.

Share
Download
background image

1. Functional Overview > JTAG Interface

32

Tsi578 User Manual

June 6, 2016

Integrated Device Technology

www.idt.com

•

CBUS compatibility

— Tsi578 does not provide the DLEN signal

— Tsi578 does not respond as a CBUS device when addressed with the CBUS address. The 

Tsi578 will interpret the CBUS address like any other 7-bit address and compare it to its 
device address without consideration for any other meaning.

•

Fast Mode or High-Speed Mode (HS-MODE)

•

Reserved 7-bit addresses should not be used as the Tsi578’s 7-bit address. If a reserved address is 
programmed, the Tsi578 will respond to that address as though it were any other 7-bit address with 
no consideration of any other meaning.

•

10-bit addressing

— Tsi578 must not have its device address programmed to the 10-bit address selection 

(11110XXb) in systems that use 10-bit addressing. The Tsi578 will interpret this address like 
any other 7-bit address and compare it to its device address without consideration for any 
other meaning.

•

General Call. The general call address will be NACK’d and the remainder of the transaction 
ignored up to a subsequent Restart or Stop. 

1.8

JTAG Interface

The JTAG interface in Tsi578 is fully compliant with IEEE 1149.6 B

oundary Scan Testing of Advanced 

Digital Networks 

as well as IEEE 1149.1 

Standard Test Access Port and Boundary Scan Architecture 

standards. There are five standard pins associated with the interface (TMS, TCK, TDI, TDO and 
TRST_b) which allow full control of the internal TAP (Test Access Port) controller. 

The JTAG Interface has the following features:

•

Contains a 5-pin Test Access Port (TAP) controller, with support for the following registers:

— Instruction register (IR)

— Boundary scan register

— Bypass  register

— Device ID register

— User test data register (DR)

•

IDT-specific pin (BCE) which allows full 1149.6 compliant boundary-scan tests. This pin should 
be held high on the board.

•

Supports debug access of Tsi578’s configuration registers

•

Supports the following instruction opcodes:

— Sample/Preload

— Extest

— EXTEST_PULSE 

(1149.6)

— EXTEST_TRAIN 

(1149.6)

Summary of Contents for Tsi578
















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Tsi578

AAVARA PB5000 User Manual preview
PB5000
Brand: AAVARA Pages: 23
Cabletron Systems MMAC-Plus 9G426-02 Reference Manual preview
MMAC-Plus 9G426-02
Brand: Cabletron Systems Pages: 12
Cabletron Systems MMAC-Plus 9F310-02 Appendix preview
MMAC-Plus 9F310-02
Brand: Cabletron Systems Pages: 4
Cabletron Systems 9E423-36 Owner'S Manual preview
9E423-36
Brand: Cabletron Systems Pages: 16
cable matters 101065 Quick Start Manual preview
101065
Brand: cable matters Pages: 4
CableCreation CD0395 User Manual preview
CD0395
Brand: CableCreation Pages: 7
Patton electronics 6511RC User Manual preview
6511RC
Brand: Patton electronics Pages: 104
Raritan MCCAT18 Specifications preview
MCCAT18
Brand: Raritan Pages: 4
AMX AVS-OCT-6448-210 Product View preview
AVS-OCT-6448-210
Brand: AMX Pages: 1
C4i HDC-SPB116 User Manual preview
HDC-SPB116
Brand: C4i Pages: 7
Broadcast Pix Flint LE 1000 Operator'S Manual preview
Flint LE 1000
Brand: Broadcast Pix Pages: 478
Black Box LGB5028A Installation Manual preview
LGB5028A
Brand: Black Box Pages: 44
Generac Power Systems RTSX100A3 Specification preview
RTSX100A3
Brand: Generac Power Systems Pages: 2
Optical Systems Design OSD2251P Series Operator'S Manual preview
OSD2251P Series
Brand: Optical Systems Design Pages: 48
Taiden HCS-4310M User Manual preview
HCS-4310M
Brand: Taiden Pages: 4
Maestro MS-VPS6M2N-DV Manual preview
MS-VPS6M2N-DV
Brand: Maestro Pages: 2
NightStick 400B-RPS Instructions For Installing preview
400B-RPS
Brand: NightStick Pages: 2
SDMO VERSO 50 Instruction Manual preview
VERSO 50
Brand: SDMO Pages: 24

Brands by name

Popular brands

Load more brands