IDT Tsi578 User Manual Download

Page: 178 / 527

7. I

C Interface > Events versus Interrupts

178

Tsi578 User Manual

June 6, 2016

Integrated Device Technology

www.idt.com

Figure 38: I

C Event and Interrupt Logic

Table 22

shows the mapping of interrupts in the

“I

C Interrupt Status Register”

to the events in the

“I

Event and Event Snapshot Registers”

. Any asserted and enabled event sets the corresponding interrupt

status, and clearing an asserted interrupt status bit clears all the related and enabled events.

Table 22: I

C Interrupt to Events Mapping

Interrupt Status Bit

Events Related to Interrupt

OMB_EMPTY (Outgoing Mailbox Empty)

OMBR (Outgoing Mailbox Read Event)

IMB_FULL (Incoming Mailbox Full)

IMBW (Incoming Mailbox Write Event)

BL_FAIL (Boot Load Fail)

BLTO (Boot Load Timeout Error)

BLERR (Boot Load Error Event)

BLSZ (Boot Load Size Error Event)

BLNOD (Boot Load No Device Event)

Bit N

I2C_INT_STAT

Bit N

I2C_INT_ENABLE

Bit 0 Enable

Write 1 to bit N in I2C_EVENT to CLEAR

AND

Read I2C_INT_STAT to copy all asserted

Interrupt Signal to
Interrupt Controller

AND

Bit 31 Enable

Bit N

I2C_NEW_EVENT

Bit N

I2C_EVENT_ENB

Write 1 to bit N in I2C_NEW_EVENT

Event Asserted by Logic SETS

Write 1 to bit N in I2C_EVENT to CLEAR

AND

Bit N

I2C_SNAP_EVENT

Read I2C_INT_STAT to CLEAR (after snapshot)

new events to snapshot register

Write 1 to related status bit in I2C_INT_STAT to CLEAR

Bit N

I2C_EVENT

AND

Other related

event(s)+
enb(s) if any

or to related bit in I2C_INT_SET to SET

Summary of Contents for Tsi578
















































































































































































































































































































































































































































































































































Search results

Summary of Contents for Tsi578

Reviews:

Related manuals for Tsi578

Brands by name

Popular brands

IDT Tsi578, User Manual

Search results

Summary of Contents for Tsi578

Reviews:

Related manuals for Tsi578

Brands by name

Popular brands