IDT CPS-12 User Manual Download

Page: 74 / 129

IDT CPS Registers

Revision 1.5

Integrated Device Technology, Inc.

CPS-16/12/8 User Manual

10 - 2

July 10, 2012

10.3 ADDRESS MAP

A mapping of registers to addresses exists as part of the overall memory address map of the device.

This

memory map is provided below.
For most of the registers, there is one instantiation for each port. The address on each individual register
indicates the actual address for port 0. For all other ports, there is a offset to port 0.

Table 10.2 CPS Memory Map

Base Address

Description

0x000000 - 0x000088

RIO Defined Registers

0x000000

DEV_IDENT_CAR

0x000004

DEV_INF_CAR

0x000008

ASSY_IDENT_CAR

0x00000C

ASSY_INF_CAR

0x000010

PROC_ELEM_FEAT_CAR

0x000014

SWITCH_PORT_INF_CAR

0x000018

SRC_OP_CAR

0x000030

SW_MCAST_SUP_CAR

0x000034

SW_RTE_TBL_LIM_CAR

0x000038

SW_MCAST_INF_CAR

0x000068

HOST_BASE_DEV_ID_LOCK_CSR

0x00006C

COMP_TAG_CSR

0x000070

STD_RTE_CONF_DESTID_SEL_CSR

0x000074

STD_RTE_CONF_PORT_SEL_CSR

0x000078

STD_RTE_DEF_PORT_CSR

0x000080

MCAST_MSK_PORT_CSR

0x000084

MCAST_ASSOC_SEL_CSR

0x000088

MCAST_ASSOC_OP_CSR

0x000100 - 0x0002BC

RIO Extended Feature Registers

0x000100

PORT_MAINT_BLK_HEAD

0x000120

PORT_LINK_TIME_OUT_CTRL_CSR

0x00013C

PORT_GEN_CTRL_CSR

0x000140

PORT_0_LINK_MAINT_REQ_CSR

0x000144

PORT_0_LINK_MAINT_RESP_CSR

0x000148

PORT_0_LOCAL_ACKID_CSR

0x000158

PORT_0_ERR_N_STAT_CSR

0x00015C

PORT_0_CTRL_CSR

...

Summary of Contents for CPS-12


































































































































Search results

Summary of Contents for CPS-12

Reviews:

Related manuals for CPS-12

Brands by name

Popular brands

IDT CPS-12, User Manual

Search results

Summary of Contents for CPS-12

Reviews:

Related manuals for CPS-12

Brands by name

Popular brands