background image

Section: 3 

 

IDS X64 LCD Keypad User Manual   700-411-01C   Issued August 2010 

To provide greater flexibility the panel caters for the programming of four different STAY PROFILES. Each 

STAY  PROFILE  contains  a  unique  combination  of  STAY,  BUZZ  and  ALARM  zones  that  cater  for  a 

particular STAY ARM requirement. 

 

EXAMPLE:       

PROFILE 1 might be used when the family goes to bed in the evening. In this profile, some interior zones 

may  be  programmed  as  alarm  zones  or  buzz  zones,  whereas  PROFILE  2  is  utilised  while  watching 

television when all interior zones would be bypassed. (See section 9.1 How to Select a Stay Profile.) 

3.2.1

 

How to Stay Arm                                                      

 

[#] [USER CODE] (Do not leave premises) 

 

1.

 

Select the required STAY PROFILE. (See Section 9.1) 

2.

 

Ensure that the LCD display reads „Ready to Arm‟ alongside the partition number being armed. If 

not, check that all protected doors and windows are closed and that all movement has ceased in 

the areas covered by motion detectors. 

3.

 

Press the 

[#]

 key. 

4.

 

Enter a valid 

[USER CODE]

. If an incorrect code is entered, the keypad will give an error beep. 

In the event of an error, press the 

[#]

 key and re-enter the 

[USER CODE]

5.

 

DO NOT violate the Entry/Exit zone (normally the front door). If the Entry/Exit zone is violated the 

system will arm in the AWAY mode. 

6.

 

The  LCD Keypad  will  read  „Exit  Delay‟,  the  ARM LED  will come  on and  the  keypad buzzer  will 

sound for the duration of the exit delay. 

7.

 

When the panel arms, any STAY zones will be automatically bypassed. These are displayed on 

the LCD display as solid text. Any violated zones will be displayed on the LCD display as flashing 

text. To scroll through zones which have been bypassed or violated use the 

[PANIC]

 and 

[MED]

 

keys. 

8.

 

Ensure that you enter only those areas that are bypassed. 

3.2.2

 

Quick Stay Arm - Shortcut Key                                              

 

(Hold down the [5] key for 2 seconds until the keypad buzzer sounds) 

 

It is possible to STAY arm by holding down the 

[5]

 key until the keypad buzzer sounds. The panel will 

immediately arm into stay mode without any exit delay. Holding the

 

[5] 

key again will toggle between the 

4 stay profiles. 

The LCD display will read „Stay Armed‟ and will indicate any zones that have been bypassed. One is able 

to scroll through the list of bypassed, as well as violated, zones by using the 

[PANIC]

 and 

[MED]

 keys. 

 

Quick Select Method: 

 

Press the [5] key simultaneously with the [PROFILE NUMBER] and release  

 

1.

 

Ensure that the Panel is disarmed. 

2.

 

Press the

 

[#]

 key to clear any previous entries. 

3.

 

Press the 

[5]

 key and then simultaneously press keys 

[1]

[2]

[3]

, or 

[4]

 – depending on the 

stay profile you want to choose – then release both keys.  

4.

 

A beep will sound to indicate successful selection of a profile. 

5.

 

Program STAY and BUZZ zones for the profile (see sections 9 and 10), and/or ARM the profile 

(with the 

[5]

 key). 

Summary of Contents for X64

































Reviews: