IDS Digital Wireless Remote Receiver
IDS Digital Wireless Remote Receiver
IDS Digital Wireless Remote Receiver
7. Programming the Unit in Stand-Alone
Mode. (Normal Settings)
These settings may be adjusted during normal
operation and it is not necessary to power the unit
down for the settings to take effect.
Remote Arm or Disarm 3 Minute Retrigger Protecting:
1. Switch Dip switch 2 ON to enable retrigger
protecting
Learning New Remotes:
1. Switch Dip switch 3 ON to enable learning of new
remotes
2. Press any button on the remotes to be learned.
3. Switch Dip switch 3 OFF to exit the learn mode.
To indicate the Ambient Noise Level:
N.B. This function must be disabled during normal
operation
This function allows the testing of ambient noise in
the environment surrounding the receiver during
installation.
1. Switch Dip switch 4 ON to enable noise level
testing.
2. ONLY install the receiver in an environment with
Normal or Better Noise Levels.
During Noise Testing the LED’s indicate the following:
2. Press any button on the remotes to be learned.
3. Switch Dip switch 6 OFF to exit the learn mode.
Disable the 3 second Hold for Panic Feature:
1. To disable the 3 second hold for panic feature on
ALL remotes switch Dip switch 7 ON.
Changing the Relays from Pulsing to Toggling:
1. Remove power from the unit by removing jumper
J5 and switch all Dip switches OFF.
2. Switch Dip switches 5, 6, 7 & 8 on.
3. Restore the power to the Unit by replacing J5.
4. To select toggling relays, use Dip switches 1, 2, 3
& 4 for Relays 1, 2, 3 & 4.
5. Switch Dip switch 8 off.
6. Wait for the LED’s to start alternating.
7. Switch all Dip switches off and set Dip switches to
the desired setting.
8. Programming a Unit Connected to a
DIGITAL IDS alarm panel.
When connected to a DIGITAL IDS alarm panel,
programming of the unit is as for the Stand-Alone
mode with the following exceptions.
9. Connector, Switch and Jumper Positions
10. Program Summary and LED Indications:
S w i t c h S e t t i n g s
R G
F u n c t i o n
1 2 3 4 5 6 7 8
~ ~ ~ ~ ~ ~ 1 0
1 0 P A N I C D I S A B L E
~
~
~ ~ ~ 1 ~ 0
1 2 L E A R N P A N I C
~
~
~ ~ 1 ~ ~ 0
2
0 E R R O R R E L A Y
~
~
~
1 ~ ~ ~ 0
1 0 T E S T N O I S E
~
~
1 ~ ~ ~ ~ 0
1 4 L E A R N
~
1 ~ ~ ~ ~ ~ 0
1 0 R E T R I G P R O T E C T
1 ~ ~ ~ ~ ~ ~ 0
1 0
0
0 0 0 0 0 1 1 3
0 P U L S E P E R I O D
RED
LED
GREEN
LED
NOISE
LEVEL
Learning and Deleting Individual User Remotes:
1. To learn a new user remote, leave Dip switch 3
0
0 0 0 0 1 0 1 4
3 S A F E / S E C U R E
0
0 0 0 0 1 1 1 4
0 P A N I C R E L A Y
0
0 0 0 1 0 0 1 4
1 R E L A Y F O R
OFF
OFF
VERY LOW
OFF
SLOW
LOW
OFF
FAST
NORMAL
SLOW
ON
HIGH
FAST
ON
VERY HIGH
ON
ON
POSSIBLE JAMMING
Enabling the Device Failure Relay Output:
1. Switch Dip switch 5 ON
ON. (it need not be switched OFF for normal
operation when connected to an IDS DIGITAL
alarm panel)
2. Follow the user manual of the DIGITAL IDS alarm
panel for learning new users.
Learning New Supervised RF Devices and deleting
Devices by Zone allocation:
1. Follow the user manual of the DIGITAL IDS alarm
panel for learning new RF devices and deleting
RF devices by zone.
0
0 0 0 1 0 1 1 3
1 R E L A Y R E T R I G G E R
0
0 0 0 1 1 0 1 0
4 R E L A Y F O R D E V I C E
0
0 0 1 0 0 0 1 0
3 P A N I C B U T T O N
0
0 1 0 0 0 0 1 0
3 A R M B U T T O N
0
1 0 0 0 0 0 1 0
3 S T A Y B U T T O N
0
0 0 1 0 0 1 1 2
1 E R R O R R E L A Y
0
0 1 0 0 0 1 1
1 3 L E A R N D E V I C E
0
1 0 0 0 0 1 1 3
2 R E C E I V E R I D
0
0 0 0 1 1 1 1
1 2
R E L A Y P U L S E /
T O G G L E
0
0 1 0 1 1 1 1 4
4 D E L E T E D E V I C E S
0
1 0 0 1 1 1 1 4
4 D E L E T E R E M O T E S
1 0 0 0 1 1 1 1 3
3 F A C T O R Y R E S E T S
Learn New Panic Remotes:
1. Switch Dip Switch 6 ON
0 = O F F
R = R E D L E D
1 = O N
G = G R E E N L E D
2 = B L I N K
3 = F A S T
4 = S L O W
5 = A L T
3
4 M E M O R Y F U L L
1
1 B U S Y S I G N A L
0
0 I N V A L I D S I G N A L
5
5 L O W B A T T
IDS 700-284-3 JULY 2005 REV B VER 1.40
10
11
12
