IDK MSD-702UHD User Manual Download Page 129

Page: 129 / 150

MSD-701UHD / 702UHD / 801UHD/ 802UHD User’s Guide

129

9.17.8 Sink device status

Menu Top

→

OTHERS

→

MONITOR STATUS

Values to be displayed [Table 9.46] Sink device status

You can view the status of sink device connected to video output connectors.

[Table 9.46] Sink device status

All video output connector

Each video output connector

Display

OUT 1A 1B 2A 2B
S N E

[OUT1A MONITOR] H24
HDCP 2.2 SUPPORT AAA

Upper

Video output channel

Output channel, output signal, color depth

Lower

HDCP status

HDCP status, error code

■

HDCP authorization status

[Table 9.47] HDCP authorization status

Character

HDCP status

Description

HDCP 2.2 SUPPORT

HDCP 2.2-compliant sink device is connected.

HDCP 1.4 SUPPORT

HDCP 1.4-compliant sink device is connected.

HDCP NOT SUPPORT

Non-HDCP-compliant sink device is connected.

HDCP ERROR

HDCP-compliant sink device is connected, but the authorization

failed.

HDCP CHECK NOW

Sink device status is being checked.

MONITOR DISCONNECT

Monitor was disconnected (displayed only for 1 second).

UNCONNECTED

No sink device is connected.

■

Output signal and color depth

H24 : HDMI, 24-BIT COLOR

H30 : HDMI, 30-BIT COLOR

: DVI

Summary of Contents for MSD-702UHD























































































































































Search results

Summary of Contents for MSD-702UHD

Reviews:

Brands by name

Popular brands

IDK MSD-702UHD, User Manual

Search results

Summary of Contents for MSD-702UHD

Reviews:

Brands by name

Popular brands