background image

m20nmdl3sm-rev0814 

 Model M20 Non-Metallic Page 10 

TROUBLESHOOTING

Possible Symptoms:

• 

Pump will not cycle.

• 

Pump cycles, but produces no flow.

• 

Pump cycles, but flow rate is 

unsatisfactory.

• 

Pump cycle seems unbalanced.

• 

Pump cycle seems to produce 

excessive vibration.

What to Check: 

Excessive suction lift 

in system.

Corrective Action: 

For lifts exceeding 

20 feet (6 meters), filling the pumping 

chambers  with  liquid  will  prime  the 

pump in most cases.

What to Check: 

Excessive  flooded 

suction in system.

Corrective Action: 

For  flooded 

conditions exceeding 10 feet (3 meters) 

of liquid, install a back pressure device.

What to Check: 

System head exceeds 

air supply pressure.

Corrective Action: 

Increase  the 

inlet  air  pressure  to  the  pump.  Most 

diaphragm pumps are designed for 1:1 

pressure ratio at zero flow.

What to Check: 

Air supply pressure or 

volume exceeds system head.

Corrective Action: 

Decrease inlet 

air  pressure  and  volume  to  the 

pump  as  calculated  on  the  published 

PERFORMANCE  CURVE.  Pump  is 

cavitating the fluid by fast cycling.

What to Check: 

Undersized  suction 

line.

Corrective Action: 

Meet  or  exceed 

pump connection recommendations 

shown  on  the  DIMENSIONAL 

DRAWING.

What to Check: 

Restricted or 

undersized air line.

Corrective Action: 

Install a larger 

air line and connection. Refer to air 

inlet recommendations shown in your 

pump’s SERVICE MANUAL.

What to Check: 

Check ESADS+Plus, 

the  Externally  Serviceable  Air 

Distribution System of the pump.

Corrective Action: 

Disassemble and 

inspect the main air distribution valve, 

pilot valve and pilot valve actuators. 

Refer to the parts drawing and air valve 

section  of  the  SERVICE  MANUAL. 

Check for clogged discharge or closed 

valve before reassembly.

What to Check: 

Rigid pipe connections 

to pump.

Corrective Action: 

Install  flexible 

connectors and a  surge suppressor.

What to Check: 

Blocked air exhaust 

muffler.

Corrective Action: 

Remove  muffler 

screen, clean or de-ice and reinstall. 

Refer to the Air Exhaust section of your 

pump SERVICE MANUAL.

What to Check: 

Pumped  fluid  in  air 

exhaust muffler.

Corrective Action: 

Disassemble 

pump chambers. Inspect for diaphragm 

rupture  or  loose  diaphragm  plate 

assembly.  Refer  to  the  Diaphragm 

Replacement section of your pump 

SERVICE MANUAL.

What to Check: 

Suction side air 

leakage or air in product.

Corrective Action: 

Visually inspect 

all  suction  side  gaskets  and  pipe 

connections.

What to Check: 

Obstructed  check 

valve.

Corrective Action: 

Disassemble  the 

wet  end  of  the  pump  and  manually 

dislodge obstruction in the check valve 

pocket.  Refer  to  the  Check  Valve 

section of the pump SERVICE MANUAL 

for disassembly instructions.

What to Check: 

Worn or misaligned 

check valve or check valve seat.

Corrective Action: 

Inspect  check 

valves and seats for wear and proper 

seating. Replace if necessary. Refer 

to  Check  Valve  section  of  the  pump 

SERVICE MANUAL for disassembly 

instructions.

What to Check: 

Blocked suction line.

Corrective Action: 

Remove  or  flush 

obstruction. Check and clear all suction 

screens and strainers.

What to Check: 

Blocked  discharge 

line.

Corrective Action: 

Check  for 

obstruction  or  closed  discharge  line 

valves.

What to Check: 

Blocked  pumping 

chamber.

Corrective Action: 

Disassemble 

and  inspect  the  wetted  chambers 

of  the  pump.  Remove  or  flush  any 

obstructions.  Refer  to  the  pump 

SERVICE MANUAL for disassembly 

instructions.

What to Check: 

Entrained air or vapor 

lock in one or both pumping chambers.

Corrective Action: 

Purge  chambers 

through  tapped  chamber  vent  plugs. 

PURGING  THE  CHAMBERS  OF 

AIR CAN BE DANGEROUS! Contact 

the  MARATHON  Technical  Services 

Department  before  performing  this 

procedure. A  model  with  top-ported 

discharge  will  reduce  or  eliminate 

problems with entrained air.

If your pump continues to perform 

below your expectations, contact your 

local MARATHON Distributor or factory 

Technical Services Group for a service 

evaluation.

WARRANTY

Refer to the enclosed MARATHON 

Warranty Certificate.

Summary of Contents for Warren Rupp MARATHON M20





































Reviews: