background image

 

 

187 

6.

 

SAM SETUP/CONFIGURATION 

The following subparagraphs explain the advanced settings available on the SAM Control Center 

and the SAM Pump Controller. 

 

PERFORMING ANY PROCEDURE IN THIS SECTION CAUSES SAM TO EXIT BOTH AUTO 

AND MANUAL MODES AND ENTER CONFIGURATION MODE. 
LEAVING SAM IN CONFIGURATION MODE PREVENTS SAM FROM ENTERING AUTO OR 

MANUAL MODES. ALWAYS TOUCH THE SEND BAM + REBOOT TO GUI OR REBOOT TO 

GUI BUTTON BEFORE RETURNING THE APPARATUS TO SERVICE. 

6.1.

 

SAM Control Center Setup/Configuration 

To access advanced settings for the SAM Control Center, enter the Technician Level 2 password 

(see Table 3, page 36). Touch the BAM TAB and then touch the Configuration Settings button. 

NOTE 

The touchscreen will reboot into Configuration Mode. 

6.1.1

 

How To Set Time And Date 

While in SAM Configuration Mode (Figure 156), touch the RTC Config button and enter the cur-

rent date and time. See Figure 157. 

 

Figure 156.  SAM Configuration Mode MENU Screen 

 

Figure 157.  Real Time Clock Screen 

Summary of Contents for Hale Sam
































































































































































































































Reviews: