Idex Hale Sam Technical Manual Download Page 197

Page: 197 / 223

177

5.2.2

Pressure Procedures (SAM Control Center)

DISENGAGE PUMP BEFORE PERFORMING CALIBRATION, OTHERWISE UNEX-

PECTED/UNDESIRABLE AUTOMATED OPERATIONS MAY OCCUR DURING CALIBRATION.

DO NOT EXCEED OPERATING PRESSURE LIMITS OF PUMP, INSTALLED PLUMBING,

HOSE(S), OR EQUIPMENT IN USE DURING CALIBRATION.

NOTES

The Valve Pressure calibration will calibrate all pressure sensors in the system at the

same time , including the intake and discharge pressure sensors.
The Akron Brass Style 9327 Navigator Mini Valve Controller does NOT support pres-

sure calibration.

Open all drains and valves to ensure pump is empty. (No water.)

Touch ZERO PRESSURES BUTTON.

Figure 145. Zero Pressure Sensor Screen

Close all drains and valves.
a)

Fill pump with water and increase pressure to 200 psi.

Touch SPAN PRESSURES button.

Touch Home button.

Cycle SAM system power.

Summary of Contents for Hale Sam
































































































































































































































Search results

Summary of Contents for Hale Sam

Reviews:

Related manuals for Hale Sam

Brands by name

Popular brands

Idex Hale Sam, Technical Manual

Search results

Summary of Contents for Hale Sam

Reviews:

Related manuals for Hale Sam

Brands by name

Popular brands