Identiv uTrust TS User Manual Download Page 15

                                uTrust TS Contact Keypad Reader 

 

 

 

Page 15 of 15 

 

 

 

9.0  Certifications  

9.1 

FCC  

This device complies with Part 15 of the FCC Rules.  Operation is subject to the following two 
conditions:  
 (1)  This device may not cause harmful interference, and 
 (2)  This device must accept any interference received, including interference that may cause        
undesired operation 

 

This  equipment  has  been  tested  and  found  to  comply  with  the  limits  for  a  Class  B  digital 
device,  pursuant  to  part  15  of  the  FCC  Rules.  These  limits  are  designed  to  provide 
reasonable protection against harmful interference in a residential installation. This equipment 
generates  uses  and  can  radiate  radio  frequency  energy  and,  if  not  installed  and  used  in 
accordance  with  the  instructions,  may  cause  harmful  interference  to  radio  communications. 
However,  there  is  no  guarantee  that  interference  will  not  occur  in  a  particular  installation.  If 
this equipment does cause harmful interference to radio or television reception, which can be 
determined by turning the equipment off and on, the user is encouraged to try to correct the 
interference by one or more of the following measures: 
 
—Reorient or relocate the receiving antenna. 
—Increase the separation between the equipment and receiver. 
—Connect the equipment into an outlet on a circuit different from that to which the receiver is 
connected. 
—Consult the dealer or an experienced radio/TV technician for help. 

 

Information to user 

 

Changes or modifications not expressly approved by 

Identiv could

 void the user's authority to operate 

the equipment. 

9.2 

ISED

 

This device complies with Innovation, Science and Economic Development Canada's license-   
exempt RSS standard(s). 

 
Operation is subject to the following two conditions. 

(1) This device may not cause interference 
(2) This device must accept any interference, including interference that may cause 
      undesired operation of the device 

 
Cet appareil est conforme de licence d'Innovation, Sciences et Développement économique 
Canada - aux normes RSS exemptes. 
 
Le fonctionnement est soumis aux deux conditions suivantes: 
 
(1) Cet appareil ne doit pas provoquer d'interférences 
(2) Cet appareil doit accepter toute interférence, y compris les interférences pouvant       
      fonctionnement indésirable de l'appareil 

9.3 

CE 

 

Identiv

 hereby declares that the uTrust TS Contact Keypad Reader Model 8216 is in compliance with 

the essential requirements and other relevant provisions of Directive 1999/5/EC. 

Summary of Contents for uTrust TS
















Reviews: