L
ON
W
ORKS
I
NTERFACE
M
ODULE
6
O
PEN
N
ET
C
ONTROLLER
L
ON
W
ORKS
I
NTERFACE
M
ODULE
U
SER
’
S
M
ANUAL
Wiring L
ON
W
ORKS
Interface Module
Precautions for Wiring
•
Use a twisted-pair cable to connect the L
ON
W
ORKS
interface module to the network. Do not run the network cable in
parallel with or near power lines, output lines, and motor lines. Keep the network cable away from noise sources.
•
Power down the L
ON
W
ORKS
interface module before you start wiring. Make sure wiring is correct before powering up
the L
ON
W
ORKS
interface module.
•
One or two cables can be connected to one terminal of the network interface connec-
tor. When connecting one cable, use AWG24 to AWG14 cables (core cross-section 0.2
to 2.5 mm
2
). When connecting two cables to one terminal, use the same cables of
AWG24 to AWG16 (0.2 to 1.5 mm
2
). Do not use cables of different diameters. Strip
the cable insulation as shown at right.
•
Tighten the mounting screws of the network interface connector to a recommended torque of 0.3 to 0.5 N·m.
•
Tighten the terminal screws of the network interface connector to a recommended torque of 0.5 to 0.6 N·m.
•
To prevent electrical shocks or communication error due to noises, connect the FG terminal to a proper ground using a
grounding wire of UL1015 AWG22 or UL1007 AWG18 (grounding resistance 100
Ω
maximum). Do not connect the
grounding wire in common with the grounding wire of motor equipment.
Ferrules, Crimping Tool, and Screwdriver for Phoenix Terminal Blocks
The screw terminal block of the network interface connector can be wired with or without using ferrules on the end of the
cable. Applicable ferrules for the terminal block and crimping tool for the ferrules are listed below. Use a screwdriver to
tighten the screw terminals on the L
ON
W
ORKS
interface module. Ferrules, crimping tool, and screwdriver are made by and
available from Phoenix Contact.
Type numbers of Phoenix Contact ferrules, crimping tool, and screwdriver are listed below. When ordering these products
from Phoenix Contact, specify the Order No. and quantity listed below.
• Ferrule Order No.
• Crimping Tool and Screwdriver Order No.
Applicable Wire Size
For 1-wire connection
For 2-wire connection
Pcs./Pkt.
mm
2
AWG
Phoenix Type
Order No.
Phoenix Type
Order No.
0.25
24
AI 0,25-8 YE
32 00 85 2
—
—
100
0.5
20
AI 0,5-8 WH
32 00 01 4
AI-TWIN 2 x 0,5-8 WH
32 00 93 3
100
0.75
18
AI 0,75-8 GY
32 00 51 9
AI-TWIN 2 x 0,75-8 GY
32 00 80 7
100
1.0
18
AI 1-8 RD
32 00 03 0
AI-TWIN 2 x
1-8 RD
32 00 81 0
100
1.5
16
AI 1,5-8 BK
32 00 04 3
AI-TWIN 2 x 1,5-8 BK
32 00 82 3
100
2.5
14
AI 2,5-8 BU
32 00 52 2
—
—
100
Tool Name
Phoenix Type
Order No.
Pcs./Pkt.
Crimping Tool
CRIMPFOX UD 6
12 04 43 6
1
Screwdriver
SZS 0,6 x 2,5
12 05 04 0
10
7 mm
A
For 1-wire Connection
For 2-wire connection
8.0 mm
B
8.0 mm
Ferrule
Dimension
B
AI-TWIN 2 x 0,5-8 WH
AI-TWIN 2 x 0,75-8 GY
AI-TWIN 2 x
1-8 RD
7.0 mm
AI-TWIN 2 x 1,5-8 BK
8.0 mm
Ferrule
Dimension
A
AI 0,25-8 YE
4.5 mm
AI 0,5-8 WH
AI 0,75-8 GY
AI 1-8 RD
AI 1,5-8 BK
AI 2,5-8 BU
6.0 mm
