Supplied By www.heating spares.co Tel. 0161 620 6677
3
Mexico Slimline RS445 -
Users
3.
Switch ON the electricity supply to the boiler and check that
all external controls, e.g. room thermostat etc., are ON.
4.
Set the boiler thermostat knob (A) to position 6. The pilot
solenoid valve should open and the intermittent spark
commence, continuing until the pilot is established. The
main burner will then cross-light smoothly.
Winter conditions (i.e. central heating and domestic hot
water).
The thermostat should be positioned at setting 5 or 6.
Summer conditions (i.e. domestic hot water only).
The
thermostat should be positioned at setting 2.
These settings are offered for general guidance only and other
settings may be found preferable, dependent upon the type of
system installed or as recommended by the installer.
To Shut Down the Boiler
1. For short periods
Turn the boiler thermostat knob (A) to OFF. When heating is
again required, restore the knob to its original setting.
2. For longer periods
a.
Turn the boiler thermostat knob (A) to OFF.
b.
Switch the electricity supply to OFF.
Frost Protection
If no frost protection is provided and frost is likely during a short
absence from home, leave the heating controls (if fitted) at a
reduced temperature setting.
For longer periods, the entire system should be drained -
including the domestic water supply.
If the system includes a frost thermostat then, during cold
weather, the boiler should be turned OFF at the time switch (if
fitted) ONLY. The mains supply should be left switched ON, with
the boiler thermostat left in the normal running position.
Control of Water Temperature
1.
Set the boiler thermostat knob (A) to give the required
temperature for central heating.
2.
The boiler thermostat automatically switches the boiler OFF
and ON to maintain the selected temperature.
To Relight the Boiler
Repeat the procedure 1 - 4 detailed in 'To light the boiler'.
Boiler Overheat Thermostat
The boiler is fitted with a safety 'cutout' thermostat: this
thermostat will shut down the boiler in the event of overheating.
Should this occur turn off the boiler and consult a CORGI
registered installer or in IE a competent person.
Loss of System Water Pressure
(Boilers fitted with the Overheat Thermostat Kit only)
If the red arrow on the system pressure gauge is set above zero
and the system pressure is seen to fall below this value over a
period of time then a water leak is indicated. In this event a
CORGI registered installer or in IE a competent person should
be consulted.
DO NOT FIRE THE BOILER IF THE PRESSURE HAS
REDUCED TO ZERO FROM THE ORIGINAL SETTING
Escape of Gas
Should a gas leak or fault be suspected, contact your gas
supplier
without delay.
Do NOT search for gas leaks with a naked flame.
Cleaning
For normal cleaning simply dust with a dry cloth.
To remove stubborn marks and stains, wipe with a damp cloth
and finish off with a dry cloth.
Do NOT use abrasive cleaning materials.
Maintenance
The appliance should be serviced at least once a year by a
CORGI registered installer or in IE a competent person.
Note.
The appliance model is given on the data plate, located on the
front of the boiler base plate, behind the grille assembly.
2
BOILER CONTROLS
RS boiler shown
Mex
2136
LEGEND
A
Boiler thermostat knob
All CORGI registered installers carry a CORGI ID card, and have a registration number. Both should be recorded in
your
Benchmark
Log Book. You can check your installer by calling CORGI direct on 01563 72300
THE LOG BOOK SHOULD BE COMPLETED AFTER EACH SERVICE AND KEPT WITH THESE INSTRUCTIONS
Caradon Ideal Limited
is a member of the Benchmark initiative and fully supports the aims of
the programme. Benchmark has been introduced to improve the standards of installation and
commissioning of central heating systems in the UK and to encourage the regular servicing of
all central heating systems to ensure safety and efficiency.
200945-1.p65
3/5/2004, 9:39 AM
39