manualshive.com logo in svg

Ideal-Standard ALTO ECOTHERM A4740AA, Installation Instructions Manual

Share
Download
Ideal-Standard ALTO ECOTHERM A4740AA Installation Instructions Manual Download Page 7

+

a

b

The thermostatic mixing valve must be installed in such a position that maintenance of the TMV and its 

valves and the commissioning and testing of the TMV can be undertaken.

Two 15mm inlet pipes need to be run at 150mm 

centres which will have been identified as the loca-

tion of the shower fitting and cut two holes of dia-

meter 25-30mm in the wall board. We recommend 

leaving 50mm of pipe protruding at this stage.

Place wall plate over pipework and onto 

the wall surface. A spirit level can be 

placed on the flats of the wall plate to 

ensure the level. Once at the correct 

position the two fixing holes can be 

marked. Drill two holes to suit appropri-

ate wall fixings.

7

4

 

INSTALLATION GUIDE

2

IMPORTANT

BEFORE CONNECTION, FLUSH WATER 

THROUGH PIPEWORK TO REMOVE ALL 

DEBRIS ETC. WHICH COULD DAMAGE 

THE VALVE MECHANISM

1

HOT water 

supply pipe

50mm

150

COLD water 

supply pipe

2

3

Flats on mounting plate

Mark the locations

Fig. 5   SLIDING RAIL – CATEGORY 5 HOSE RETAINING

Note:

Fixing holes in 

bracket are at 65mm 

centres.

Summary of Contents for ALTO ECOTHERM A4740AA





















Reviews:

No comments

Brands by name

Popular brands

Load more brands