IDEAL Networks SignalTEK NT Manual Download Page 36

Page: 36 / 58

SignalTEK NT

156875 Iss 3

User Guide

Page 36

Specifications - SignalTEK NT

Near-End Unit

Connectors

Test Ports

RJ45

Used for -

Cable Test (With a companion Remote Unit)

- Network Test (Connected to an active network)

Connector type -

Samtec Lifejack with user-replaceable contacts

Insertion Cycles

- 500 min

Location

- Left hand side

Optical

Used for -

Cable Test (With a companion Remote Unit)

- Network Test (Connected to an active network)

Connector type -

SFP socket

Location

- Left hand side

System Ports

USB

Used for

- Software Update

- Results transfer to memory key or via Wi-Fi adaptor

Class -

Host

Connector type -

USB type -

1.1

Location

- Top

Power

Used for

- Battery charging

- Mains powering via adaptor

Connector type -

2.5mm pin power jack

Polarity

- Centre pin positive

Voltage - 12v

Current - 2 amps

Location

- Bottom of power module

Controls

ON/OFF

Push button

Used for

- Power ON/OFF

Location

- Front

Function Keys

F1 to F3

Used for

- Screen-defined functions

Location

- Front

Navigation Keys

Cursor and ENTER

Used for

- User interface navigation

Location

- Front

Summary of Contents for SignalTEK NT



























































Search results

Summary of Contents for SignalTEK NT

Reviews:

Related manuals for SignalTEK NT

Brands by name

Popular brands

IDEAL Networks SignalTEK NT, Manual

Search results

Summary of Contents for SignalTEK NT

Reviews:

Related manuals for SignalTEK NT

Brands by name

Popular brands