background image

45

EVOMAX 

Installation & Servicing

INSTALLATION

INST

ALLA

TION

48

  INITIAL LIGHTING

OPERATING SEQUENCE

1.

  Check that the system has been filled and the boiler is not air locked - 

air in the boiler could damage the heat exchanger.  For this reason the 

airvent located in the left top side must never be shut off.

2. 

Check that all the drain cocks are closed and any valves in the flow 

and return are open.

3.

  Check that the GAS SERVICE COCK IS ON.

4.

  Fill the condensate trap with water before putting the unit into operation 

(see Frame 58 for condensate trap removal).  

5.

  Check the indication on the pressure gauge.  If the pressure is less 

than 1 bar the installation should be filled up first (sealed system only).

6.

  Switch the electricity supply ON and check that all 

the external controls are calling for heat.  Check 

boiler is set for winter operation - see Evomax user 

interface basic operating instructions.

7.

  The boiler will commence the ignition sequence.  If 

after 5 attempts the boiler has failed to light then it 

will lock out.  Press the reset button to restart the 

ignition sequence.

8. 

Operate the boiler for 10 minutes and check the gas 

rate (Table 1).  You should be able to read at least 

90% of the nominal.

Evomax   ~  Flue CO

2

 % measurements (hot condition)

30

40

60

80

100

120

150

30P

40P

60P

80P

Max Rate

9.2% - 10.2%

10.9% - 11.9%

Min Rate

8.2% - 9.2%

9.7%  - 10.7%

10.0% - 11.0%

Standby

yes

yes

yes

yes

no

no

no

no

no

no

yes

yes

Heat demand on?

Temp. < setpoint?

Demand

off or Temp. >setpoint?

Heat Demand Off?

Fan off.  Pump off

Flame detected?

Demand On

& Temp. <Set point & Anti-cycle 

done?

Fan On

20s Fan Pre-purge

Pump On

Spark Generator On

Gas Valve On

3s Ignition Period

Burner Output controlled relative to

Heat Demand by varying Fan Speed

Burner On

Spark Generator Off

1st Stabilisation Period

Gas Valve Off

Pump Overrun

Note.  The fan runs for 

4 mins after the burner 

switches off

Standby

Summary of Contents for Evomax 30



































































Reviews: