IdAutomation SC7USB 2D Programming Manual Download Page 5

Page: 5 / 137

Introduction

This scanner will automatically scan a barcode at a distance of 3 to 8

inches from the symbol when the trigger is pulled. The scanner is

programmed by scanning barcodes from the manual when viewed on

the screen at 200% or more magnification from the PDF. Successful

scanning shall be obtained by tilting the scanner with respect to the

barcode to avoid direct reflections that impair reading performance.

Installation and Setup

1.Connect the USB cable between scanner and PC.

To enable USB keyboard emulation, scan the appropriate barcode

below:

USB HID (PC)

USB HID (MAC)

3.If the scanner does not operate properly, remove the scanner from the

USB port and plug it into another port after scanning one of the USB

HID barcodes above.

4.If the scanner still does not operate properly, remove the cable from

the PC and pull the cable out of the scanner. Reinsert the cable in the

scanner.

Summary of Contents for SC7USB 2D










































































































































Search results

Summary of Contents for SC7USB 2D

Reviews:

Related manuals for SC7USB 2D

Brands by name

Popular brands

IdAutomation SC7USB 2D, Programming Manual

Search results

Summary of Contents for SC7USB 2D

Reviews:

Related manuals for SC7USB 2D

Brands by name

Popular brands