INTERNET
TELExOMi
EQUIPMENTi
()hiStandbyiDi=ackupi
RequirediforiTelecomi
Equipmenti
ETHERNET
ENxLOSURE
FIRE
SUPERVISORY
TROU=LE
FIREigLgRMiPgNELi
Z5
Z(
Z0
INPUTiEXPgNvER
xOMiSTgTUSiDiF=
)s-
)s-
gx
gx
MgINSiSUPPLY
V5(8VgxYi
ENxLOSURE
xONTROLLER
xgNDULx3S--w
INPUTiEXPgNvER
PgSSIVEixOMMUNIxgTION
Note.igllicablesishallibeiprotectediwithinimetaliconduitsX
Metalixonduit
AiEOLiresistorimustibeiinstallediatitheiFireiglarmixontroliPaneliOutputX
Valuei5 Valuei( MonitorediStatus
5K
5K
Open1ixlose1iTamper1iShort
9Ks
(K(
Open1ixlose1iTamper1iShort
58K
58K
Open1ixlose1iTamper1iShort
(K(
(K(
Open1ixlose1iTamper1iShort
)K:
(K(
Open1ixlose1iTamper1iShort
)K:
)K:
Open1ixlose1iTamper1iShort
Zg
U
X3
Z5
xO
M
xO
M
Z(
Z0
Z)
ULxicertifiedi5(VivxiPoweriSupply
Z
3
5(Vvx
5(Vvx
gUX
Z
3
Z
3
5(Vvx
Z
3
)s-
)s-
Z 3
x Nx
Nx
x
5(Vvx
gxi
FgIL
=gTT
FgIL
AiTheigxiFgILioutputionitheiPoweriSupplyiMUST beiprogrammeditoifollowitheigxiTroubleiInputiasifollows.
i gxiFgILi,iOPENionifail
PSTN
TELExOMi
EQUIPMENTi
vIgLER
Z)
Programmable
Output
NXOiInputixontactX
FireiInputimonitoringiRESETiPushi=utton
AiFireiareasishallibeiseparatedifromiburglariareasithroughiareaipartitioningX
AiFireiInputsiZ53Z0ishallibeiusediexclusivelyiforifireimonitoringiandicannotibeiprogrammeditoiactivateitheibellioutput
AFireiInputiZ)iNXOiPushi=uttonitoibeiusediasimonitoringiresetiswitchX
NXx
Tamper
NXxiInputixontact
Valuei(
Valuei5
TypicaliInputixircuits
EOL Resitor Input Configuration
Fire area inputs must be programmed as follows:
-
FACP Fire Alarm Signal input type must be programmed as Fire.
-
Supervisory Trouble Signal input type must be programmed as 24 HR Silent.
-
Trouble Signal input type must be programmed as 24 HR Silent.
Please refer to the section
Inputs | Areas and Input Types
in the Operator Reference Manual.
⦁
All fire area inputs must be placed into an area and this area must be armed. Please refer to the section
Inputs | Areas and Input Types
in the Operator Reference Manual.
⦁
COM Status
FACP system with a COM STATUS input must have this input connected to one of the dry relay contacts of
the Relay1 or Relay2 outputs of the Protege controller and the selected output must be programmed as the
Report OK output in the Contact ID Service.
Note: Any available dry relay contact on the Protege controller or output expander may be used for the
FACP system, provided the selected output is programmed as the Report OK output.
Please refer to section
Contact ID | Settings
in the Operator Reference Manual.
⦁
Fire inputs Z1-Z3 shall be used exclusively for fire monitoring and cannot be programmed to activate the
bell output.
PRT-ZX8-DIN | Protege DIN Rail 8 Input Expander | Installation Manual
29
