ICT Protege PRT-PSU-DIN-8A Installation Manual Download Page 33

Page: 33 / 36

FCC Compliance Statements

FCC Rules and Regulations CFR 47, Part 15, Class A

This equipment complies with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules.

Operation is subject to the following two conditions:

⦁

This device may not cause harmful interference.

⦁

This device must accept any interference received, including interference that may cause undesired
operation.

NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY
APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE
USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

PRT-PSU-DIN-8A | Protege DIN Rail 8A Intelligent Power Supply | Installation Manual

Summary of Contents for Protege PRT-PSU-DIN-8A





































Search results

Summary of Contents for Protege PRT-PSU-DIN-8A

Reviews:

Related manuals for Protege PRT-PSU-DIN-8A

Brands by name

Popular brands

ICT Protege PRT-PSU-DIN-8A, Installation Manual

Search results

Summary of Contents for Protege PRT-PSU-DIN-8A

Reviews:

Related manuals for Protege PRT-PSU-DIN-8A

Brands by name

Popular brands