- 4 -
FLASHES
STATUS
1
bill jammed
2
disabled
from system
3
sensor
problem
4
reserved
5
bill
box is removed
6
LED
ON
POWER
ON
LED
OFF
POWER
OFF
bill box is full of money
The two LED lights located at the front of the unit will show the operational
status of the bill validator. The LED lights will flash ON and OFF (in 500ms
intervals) when the unit is ready to accept bills. The LED lights will be OFF
if the unit is disabled or out of service, in which case the unit will not accept
any bills.
The bill validator can only accept one bill at a time. The LED lights will be
OFF and will not accept another bill while a bill is being validated in the unit.
The LED lights will start to flash normally when the bill validator is ready to
accept the next bill.
(3) LED Display
(4) LED Status
(5) Download and Upgrade
In addition to the 30-pin connector, there is also an 8-pin RJ-45 connector
on the side of the bill validator designed for the purpose of downloading
programs and updating validation software. The connector will be kept open
under normal operation of the bill validator. It will only be used when a new
software or program need to be downloaded into the flash ROM. (Figure 1)
LED
Option Switches
COM2
C
O
M
2
PH
P
H
BACK LED
Figure 1
FP-001
FP-001
5
4
3
2
1
5
4
3
2
1
9
8
7
6
9
8
7
6
5
4 3 2 1
9 8 7 6
- 5 -
A6 Pin-out Assignments (S.T.D. Pulse for 12V DC)
(6) 6-1
1
2
3
4
5
6
7
8
9
10
25
19
11
26
20
12
27
21
13
28
22
16
14
29
23
17
15
30
24
18
For the
12V DC
version of the A6 bill validator, the harness(
part no. WEL-M007
,
see page.11 for pin-out information) has a dual-in-line 30-pin peripheral connector
at one end and a 9-pin mating connector at the other end. Connect the 30-pin
connector to the side of the bill validator and the 9-pin mating connector to the
12V DC power harness (
part no.CU-961-1
, see page. 9 for pin-out information ).
9-pin mating connector pin-out assignments:
Pin 1 I Pin 6 Reserved
Pin 2 INHIBIT - Pin 7 CREDIT_RELAY(N.O.)
Pin 3 Reserved Pin 8 CREDIT_RELAY(Common)
Pin 4 Reserved Pin 9 GND (Power)
Pin 5 12V DC (Power)
Dual-in-line 30-pin peripheral connector (A6, 12V DC) pin-out assignments:
1
2
3
6
5
4
7
8
9
CAUTION:
Turn off the power before connecting or disconnecting the
bill validator.
Pin 16 - CREDIT_RELAY(N.O.)
Pin 17 - Reserved
Pin 18 - ENABLE +
Pin 19 - KEY
Pin 20 - INHIBIT -
Pin 21 - Reserved
Pin 22 - Reserved
Pin 23 - Reserved
Pin 24 - Reserved
Pin 25 - Reserved
Pin 26 - Reserved
Pin 27 - Reserved
Pin 28 - Reserved
Pin 29 - Reserved
Pin 30 - Reserved
Pin 1 - CREDIT_RELAY(Common)
Pin 2 - 12VDC (Power)
Pin 3 - ENABLE -
Pin 4 - Reserved
Pin 5 - INHIBIT +
Pin 6 - KEY
Pin 7 - Reserved
Pin 8 - Reserved
Pin 9 - Reserved
Pin 10 - GND (Power)
Pin 11 - Reserved
Pin 12 - Reserved
Pin 13 - Reserved
Pin 14 - Reserved
Pin 15 - Reserved
