background image

633GC OPERATOR’S MANUAL 

SAFETY 

 

THE FOLLOWING SYMBOL APPLIES TO ALL ITEMS LISTED ON THIS PAGE 

 
 
A potentially hazardous situation exists which, if not avoided, may 
result in minor or moderate injury or property damage. 

 

 
 

 

Always turn a diamond chainsaw OFF when performing maintenance on the saw including 
chain tensioning. 

 

 

Never use equipment that is not functioning properly.  Have the saw repaired by qualified 
service personnel.

 

 

 

Turn engine OFF before refueling.  Keep away from open flame.  Always provide for good 
ventilation when handling fuel.  Move diamond chainsaw at least 10 feet (3 m) away from 
refueling area before starting. 

 

 

SealPro™ diamond chains require a minimum water pressure of 20 psi (1.4 bar).  Insufficient 
water supply may result in excessive wear to the chain, which can lead to loss of strength and 
chain breakage.  

 

 

Never start a diamond chainsaw unless the bar, chain and side cover 
are properly installed. 

 
 
 
 
GENERAL SAFETY PRECAUTIONS 
 

 

Always wear protective clothes, including hard hat, eye protection, hearing protection, and gloves. 

 

 

Avoid loose fitting clothing. 

 

 

Perform safety checks before starting each day. 

 

 

Always operate tool with solid footing and with both hands on saw. 

 

 

Remove or control slurry to prevent slippery conditions while cutting. 

 

 

Be sure there are no obstructions (plumbing, electrical conduit, air ducts) and no unnecessary people 
present. 

 

 

Set up a well-marked safety zone with a roped boundary and clear signs. 

  

 

Provide adequate ventilation when working in an enclosed area.  Breathing exhaust gases is 
dangerous. 

 

 

To avoid electrocution, check for live electrical wiring near cutting area. 

 
 
 

 

CAUTION 

Summary of Contents for 633GC



























Reviews: