ICRealtime Edge IPEG-D20F-IRW3 User Manual Download Page 177 | Manualshive

Page: 177 / 200

background image

Flowrate Alarm

Set

Enter No.

,

Leave No.

, and

Stranded No.

The alarm is triggered

when the configured value is reached.

Regional People
Number Statistics
Alarm

Set the number of people in the people counting region. When the
people count reaches the threshold or the stay duration exceeds
the configured value, the alarm is triggered.
When you set inside number to be 0, and select the type to be

≥

Threshold

, the system will not perform the alarm linkage.

Inside Number

Type

Stranding Alarm

If enabled, set the stranding time. When the stay duration of the
people within the area exceeds the configured value, an event
will be created.

Stranding Time

Sensitivity

Set the alarm-triggered sensitivity. The higher the sensitivity, the
easier the alarm will be triggered.

Max Height

Set the maximum height of the people in the detection area. The
unit is in centimeters, and the range is 0–300.

Min Height

Set the minimum height of the people in the detection area. The
unit is in centimeters, and the range is 0–200.

Result

Step 6 Set arming periods and alarm linkage actions. For details, see "5.1.1 Alarm Linkage".
Step 7 Click

Save

.

To view alarm information on the

Alarm

tab, subscribe relevant alarm event. For details, see "5.1.2

Subscribing Alarm".

Queuing

This function counts people queued in the detection area. When the queue number exceeds the
configured number or the queue time exceeds the configured time, the system will create an event.

Prerequisites

You will first need to configure

People Counting

.

Procedure

Step 1

Select

Setting

>

Event

>

Queuing

.

Figure 5-68 Queuing

165

«
...
175
176
177
178
179
...
»

Summary of Contents for Edge IPEG-D20F-IRW3









































































































































































































Reviews:

No comments

Related manuals for Edge IPEG-D20F-IRW3

Brand: Panasonic Pages: 124

Brand: Elkron Pages: 12

Brand: NED Pages: 60

Brand: Mini Gadgets Pages: 6

Brand: VS2 Pages: 2

Brand: Planet Pages: 10

Brand: X-10 Pages: 18

Brand: SecurityMan Pages: 2

Brand: CAMDEN Pages: 2

Brand: DELTA DORE Pages: 2

SECURITY MANAGER 2000

Brand: ADT Pages: 44

Brand: IDS Pages: 8

XRX300 LED Series

Brand: WE-EF Pages: 6

Brand: MeiTrack Pages: 8

Brand: Vitek Pages: 16

Brand: AJAX Pages: 13

Brand: Ubiquiti Pages: 56

Brand: Vivitar Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands