ICRealtime Edge IPEG-D20F-IRW3 User Manual Download Page 136 | Manualshive

Page: 136 / 200

background image

Step 1

Select

Setting

>

Storage

>

Record Control

.

Figure 5-5 Record control

Step 2

Set parameters.

Table 5-1 Description of record control parameters

Parameter

Description

Pack Duration

Constant recording files are limited to the pack duration value.
For example, if set to 5, each video file with constant
recording is 5 minutes each.

Pre-event Record

The time to record the video in advance of a triggered alarm
event. For example, if the pre-event record is set to be 5 s,
the system saves the recorded video of 5 s before the alarm is
triggered.

Disk Full

Recording strategy when the disk is full.

●

Stop

: Stop recording when the disk is full.

●

Overwrite

: Cyclically overwrite the earliest video when

the disk is full.

Record Mode

When you select

Manual

, the system starts recording; when

you select

Auto

, the system starts recording in the configured

time period of record plan.

Record Stream

Select record stream, including

Main Stream

and

Sub Stream

.

Step 3

Click

Save

.

5.1.1.2.2

Setting Record Linkage

If you want the camera to record when an event (such as motion detect is triggered), check in the
Record box. The

Record Delay

value is how much time the camera will record after the event has

ended.

Figure 5-6 Record linkage

5.1.1.3

Snapshot Linkage

After snapshot linkage is configured, the IPC can automatically alarm and take snapshots when an
event is triggered. For querying and setting snapshot storage location, see "4.5.2.5 Path".

124

«
...
134
135
136
137
138
...
»

Summary of Contents for Edge IPEG-D20F-IRW3









































































































































































































Reviews:

No comments

Related manuals for Edge IPEG-D20F-IRW3

EF35mm f/2 IS USM

Brand: Canon Pages: 2

EF300mm f/2.8L IS II USM

Brand: Canon Pages: 13

EF28-135mm f/3.5-5.6 IS USM

Brand: Canon Pages: 9

Brand: D-Link Pages: 4

Brand: EasyN Pages: 11

Brand: Barnett Engineering Pages: 3

Brand: Olympus Pages: 374

Brand: Olympus Pages: 66

Brand: M-system Pages: 3

Brand: Axis Pages: 2

Brand: Axis Pages: 2

Mainline CV-M13B10-ODI

Brand: Clare Controls Pages: 36

Kasa Smart KC310

Brand: TP-Link Pages: 23

Brand: bettini Pages: 76

Brand: Visionhitech Pages: 2

Brand: Velleman Pages: 16

Brand: DMP Electronics Pages: 2

MWS3A-PRM-2CH-NC

Brand: CP Electronics Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands