ICRealtime Edge IPEG-D20F-IRW3 User Manual Download Page 85

Page: 85 / 200

Step 2

Select the

Enable

checkbox, draw the area on the image, and then configure the image

quality of ROI.

●

You can draw four area boxes at most.

●

The higher the image quality value is, the better the quality will be.

●

Click

Remove All

to delete all the area boxes; select one box, and then click

Delete

right-click to delete it.

Step 3

Click

Save

4.5.2.5

Path

This section allows you to configure the storage path for live snapshot, live record, playback snapshot,
playback download, and video clips. This section is only available when using Internet Explorer with
plugins installed.
Step 1

Select

Setting

Camera

Video

Path

Figure 4-69 Path

Step 2

Click

Browse

to select the storage path for live snapshot, live record, playback snapshot,

playback download, and video clips.

Table 4-20 Description of path

Summary of Contents for Edge IPEG-D20F-IRW3









































































































































































































Search results

Summary of Contents for Edge IPEG-D20F-IRW3

Reviews:

Related manuals for Edge IPEG-D20F-IRW3

Brands by name

Popular brands

ICRealtime Edge IPEG-D20F-IRW3, User Manual

Search results

Summary of Contents for Edge IPEG-D20F-IRW3

Reviews:

Related manuals for Edge IPEG-D20F-IRW3

Brands by name

Popular brands