manualshive.com logo in svg

ICP Electronics PCISA-3717EVT, User Manual, Page: 37 / 46

Share
Download
ICP Electronics PCISA-3717EVT User Manual Download Page 37

 

PCISA-3717EVT Socket 370 Celeron

TM

 & Pentium III 

®

                           

with Ethernet , VGA( Dual Display ) ,  
 TV-Out , Audio  Board 
 

71

Should Have EISA Board But Not Found 
PLEASE RUN EISA CONFIGURATION UTILITY 

The board installed is not responding to the ID request, or no board ID has been 
found in the indicated slot. 

NOTE:   When this error appears, the system will boot in 
ISA mode, which allows you to run the EISA Configuration 
Utility. 

Slot Not Empty 

Indicates that a slot designated as empty by the EISA Configuration Utility 
actually contains a board. 

NOTE:  When this error appears, the system will boot in ISA 
mode, which allows you to run the EISA Configuration Utility. 

SYSTEM HALTED, (CTRL-ALT-DEL) TO REBOOT ... 

Indicates the present boot attempt has been aborted and the system must be 
rebooted.  Press and hold down the CTRL and ALT keys and press DEL. 

Wrong Board In Slot 
PLEASE RUN EISA CONFIGURATION UTILITY 

The board ID does not match the ID stored in the EISA non-volatile memory. 

NOTE:  When this error appears, the system will boot in ISA 
mode, which allows you to run the EISA Configuration Utility. 

 FLOPPY DISK(S) fail (80) 

→

 Unable to reset floppy subsystem. 

FLOPPY DISK(S) fail (40) 

→

 Floppy Type dismatch. 

 Hard Disk(s) fail (80)         

→

 HDD reset failed 

Hard Disk(s) fail (40)         

→

 HDD controller diagnostics failed. 

PCISA-3717EVT Socket 370 Celeron

TM

 & Pentium III 

®

                           

with Ethernet , VGA( Dual Display ) ,  
 TV-Out ,Audio  Board 

72

 Hard Disk(s) fail (20)         

→

 HDD initialization error. 

 Hard Disk(s) fail (10)         

→

 Unable to recalibrate fixed disk. 

 Hard Disk(s) fail (08)         

→

 Sector Verify failed. 

Keyboard is locked out - Unlock the key. 

BIOS detect the keyboard is locked. P17 of keyboard controller is pulled 
low. 

Keyboard error or no keyboard present. 

Cannot initialize the keyboard.  Make sure the keyboard is attached 
correctly and no keys are being pressed during the boot.

 

Manufacturing POST loop. 

System will repeat POST procedure infinitely while the P15 of keyboard 
controller is pull low.  This is also used for M/B burn in test.

 

BIOS ROM checksum error - System halted. 

The checksum of ROM address F0000H-FFFFFH is bad. 

Memory test fail. 

BIOS reports the memory test fail if the onboard memory is tested error. 

 
 
 
 
 

 
 
 

 

Appendix C.  

Summary of Contents for PCISA-3717EVT















































Reviews:

No comments