manualshive.com logo in svg

ICP DAS USA ET-7H16M Series, User Manual, Page: 15 / 84

Share
Download
ICP DAS USA ET-7H16M Series User Manual Download Page 15

 

PET-7H16M Series User Manual, version 1.0.1                                                                                  P.15 

 

LED Indicators 

The PET-7H16M has 3 LED indicators shown as below. 

LED Indicator 

LED Action  Meaning 

L1 

PoE 

ON 

When unit power is supplied via PoE. 

L2 

Link/ACT 

ON 

Ethernet link detected 

OFF 

No Ethernet link detected 

Flashing 

Ethernet packet received 

L3 

RUN 

Flashing 

Firmware is running 

 

 

Tips & Warnings 

If the Run LED does not display the information as above, the following steps 
should be taken: 

Step 1

: Switch the power off 

Step 2

: Switch the power on and double-check the LED indicators 

 

 

 

 

Ethernet Port 

The PET-7H16M has an Ethernet port that can be connected to a computer or device via an 

Ethernet cable. 

 

The L2 indicators display the status of the 

Ethernet port. 

 

 

 

 

Summary of Contents for ET-7H16M Series





















































































Reviews:

No comments