background image

 

 

A-812PG 

 

Hardware User’s Manual 

 

 

 

 

 

 

 

Warranty

 

All products manufactured by ICP DAS are warranted against defective materials for a 

period of one year from the date of delivery to the original purchaser. 

 

Warning 

ICP DAS assume no liability for damages consequent to the use of this product. ICP 

DAS reserves the right to change this manual at any time without notice. The information 

furnished by ICP DAS is believed to be accurate and reliable. However, no responsibility is 

assumed by ICP DAS for its use, nor for any infringements of patents or other rights of third 

parties resulting from its use. 

 

Copyright

 

Copyright 1997 by ICP DAS. All rights are reserved. 

 

Trademark

 

The names used for identification only may be registered trademarks of their respective 

companies. 

 

License

 

The user can use, modify and backup this software 

on a single machine.

 

The user may not reproduce, transfer or distribute this software, or any copy, in whole or in 

part. 

                A-812PG Hardware Manual (Ver.1.2, Sep/2005, IPH-004-12)   -----  

1

 

Summary of Contents for A-812PG






































Reviews: