background image

19

HOW TO TURN ON THE POWER

IMPORTANT: If the treadmill has been exposed to 

cold temperatures, allow it to warm to room tem-

perature before you turn on the power. If you do 

not do this, you may damage the console displays 

or other electrical components.

Plug in the power cord (see 

page 17). Next, locate the 

power switch (I) on the 

treadmill frame near the 

power cord. Make sure that 

the switch is in the reset 

position. 

IMPORTANT: The console may feature a demo 

mode, designed to be used if the treadmill is dis-

played in a store. If the displays light as soon as 

you plug in the power cord and press the power 

switch into the reset position, the demo mode is 

turned on. To turn off the demo mode, hold down 

the Stop button for a few seconds. If the displays 

remain lit, see THE SETTINGS MODE on page 23 to 

turn off the demo mode. 

Next, stand on the 

foot rails of the tread-

mill. Find the clip (J) 

attached to the key 

(K), and slide the clip 

onto the waistband of 

your clothes. Then, 

insert the key into 

the console. After a 

moment, the displays 

will light. IMPORTANT: In an emergency, the key can 

be pulled from the console, causing the walking 

belt to slow to a stop. Test the clip by carefully tak-

ing a few steps backward; if the key is not pulled 

from the console, adjust the position of the clip.

IMPORTANT: Before you use the treadmill, take the 

following steps to ensure that the console shows 

the correct incline level of the treadmill. First, 

press the Incline increase button once. Next, press 

either the Incline decrease button or the lowest 

numbered Incline button to set the treadmill to its 

lowest setting. When the frame stops moving, the 

treadmill is ready for use.

HOW TO USE THE MANUAL MODE

1.    Insert the key into the console. 

   See HOW TO TURN ON THE POWER at the left.

2.  

Select the manual mode.

   When the key is inserted, the manual mode will be 

selected. If you have selected a workout, press the 

Manual button. Only zeros should appear in the 

display.

3.  

Start the walking belt.

   To start the walking belt, press the Start button or 

one of the numbered Speed buttons. 

    If you press the Start button, the walking belt will 

begin to move at 1 mph. As you exercise, change 

the speed of the walking belt as desired by press-

ing the Speed increase and decrease buttons. 

Each time you press one of the buttons, the speed 

setting will change by 0.1 mph; if you hold down 

the button, the speed setting will change in incre-

ments of 0.5 mph. 

   If you press one of the numbered Speed buttons, 

the walking belt will gradually change speed until 

it reaches the selected speed setting. To select a 

speed setting that includes a decimal—such as 

3.5 mph—press two numbered buttons in suc-

cession. For example, to select a speed setting of 

3.5 mph, press the 3 button and then immediately 

press the 5 button. Note: This feature will not func-

tion when the console is set to metric units.

   To stop the walking belt, press the Stop button. 

The time will begin to flash in the display. To restart 

the walking belt, press the Start button or one of 

the numbered Speed buttons. 

I

ETPF50920C

K

J

Summary of Contents for PROFORM PFTL50920C.1





































Reviews: