INSTRUCTIONS
POWER AMPLIFIER UNITS
UR-PA5000
Thank you for purchasing the UR-PA5000/UR-
PA6000
power
amplifier
units
for the IC-FR5000/IC-
FR6000 series repeaters.
Please read these instructions and the repeater’s
instruction manual carefully before installing the
units and operating the repeater.
q
Set screws (M3
×
6 mm) ........................................4
w
Tapping screws (M3
×
8 mm) .................................2
e
Coaxial cable (OPC-2243) ...................................1
r
DC power cable....................................................1
1 mm =
1
/
32
inch
q
Remove the 7 screws from top and the 2 screws
from each side of the repeater, then slide off the top
cover to the direction of the arrow.
w
Remove the 3 screws from bottom and the 2
screws from each side of the repeater.
e
Disconnect the control cable from the channel
module, then remove the front panel.
r
Remove the 5 screws to remove the front plate off.
Front plate
Front panel
P0
P1
P2
P3
P4
P0
P1
P2
P3
P4
P0
P1
P2
P3
P4
Channel module
Front panel
SUPPLIED ACCESSORIES
OPENING CASE
UR-PA6000
w
q
e
r
Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incor-
porated (Japan) in Japan, the United States, the United Kingdom, Germany,
France, Spain, Russia and/or other countries.
All other products or brands are registered trademarks or trademarks of their
respective holders.
• FOR CLASS A UNINTENTIONAL RADIATORS:
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide rea-
sonable protection against harmful interference when the
equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be re-
quired to correct the interference at his own expense.
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
A-7027H-1EX
Printed in Japan
© 2012 Icom Inc.
LOCATING THE UNIT
Before installing the power amplifier unit, relo-
cation of the channel module is necessary.
Otherwise, the amplifier's ventilation system
will not work properly and may damage the
unit.
q
Detach the support bracket by removing the set
screws, as illustrated below.
w
Detach the channel module by removing the 8 M3
tapping screws and the 6 M3 set screws.
e
Reinstall it on the right side (front view) of the base.
r
Install the power amplifier unit with the fans facing
the front of the repeater.
• Tighten only 3 set screws and 2 tapping screws at this
time, as illustrated below.
Set screws
Tapping
screws
Power amplifier unit
Channel module
Set screws
Tapping
screws
Channel module
Support bracket
t
When both module and amplifier are installed, at-
tach the support bracket with the set screws to the
original location, on the amplifier's angle.
• The inmost part of the bracket will be tightened along
with the amplifier's angle.
Support bracket
Power amplifier unit
Channel module
q
Connect the control cable to the channel module.
w
Return the front panel, top cover and screws to
their original positions.
P0
P1
P2
P3
P4
Control cable
Power amplifier unit
Channel module
P0
P1
P2
P3
P4
ASSEMBLE THE UNIT
REQUIRED
NOTE:
The cables are not
supplied with the the power
amplifier unit.
•
OPC-2202
connection
cable
Connects between the repeater
unit and the PA unit.
•
OPC-2203
connection
cable
Connects between the repeater
unit, the PA unit and the external
equipment, if used.
OPC-2202
OPC-2203
Before installing the power amplifier unit, one of the following
cables is required.
