background image

12

4

PROGRAMMABLE FUNCTIONS

11

4

PROGRAMMABLE FUNCTIONS

General

In the following explanations, programmable function names are
bracketed, the specific switch used to activate the function depends
on programming.

D

D

KEYPAD LOCK FUNCTION

This function locks access to all programmable switches (except
the switch assigned for the lock function).
:
Push and hold the [LOCK] switch for 1 sec. to toggle the lock func-
tion ON and OFF.
• “

”appears while the lock function is ON.

• This function may be inhibited on some channels.

D

D

PRIORITY CHANNEL

This function is used to select a pre-programmed channel at the
push of a switch.

Push the [PRIORITY] switch to select the priority channel.
• “PRIO” appears briefly, then the priority channel is automatically
selected.

D

D

SCAN FUNCTION

The scan function allows you to search a pre-programmed group
of channels for signals.

Push the [SCAN] switch to start/stop scan.
• Scan pauses on a channel when receiving a signal.
• Depending on programming, a message may appear while scan-

ning.

• “Lockout SCAN” (pre-programmed list SCAN) or “Priority SCAN”

can be pre-programmed.

• When  the  “Power-save function” is activated, the transceiver

checks all pre-programmed channels then returns to the “Power-
save function” again.

D

D

HIGH/LOW POWER OUTPUT

This function selects high or low power for a channel.

Push the [HIGH/LOW] switch to toggle between high and low
power.
• “LOW” appears when low output power is selected.

D

D

SCRAMBLER FUNCTION (optional UT-109 #01* or UT-110 #01*

is required.)
This function provides higher communication security.
UT-109: Non-rolling type. 32 code numbers are available.
UT-110: Rolling type. 1020 (4 group 

×

255) code numbers are avail-

able.

Push the [SCRM] switch to toggle the function ON and OFF.

NOTE: NEVER use #02 High AF level versions, as they are not
compatible

D

D

BEEP FUNCTION

This function provides confirmation beep tones when pushing
switches.

Push the [BEEP] switch to toggle the function ON and OFF.

Summary of Contents for UltraTech IC-F4GT-4


















Reviews: