![background image](http://html1.mh-extra.com/html/icom/id-51a/id-51a_advanced-manual_2038182002.webp)
i
INTRODUCTION
Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the
United Kingdom, Germany, France, Spain, Russia, Australia, New Zealand, and/or other countries.
Adobe, Acrobat, and Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United
States and/or other countries.
All other products or brands are registered trademarks or trademarks of their respective holders.
About these Advanced Manual (PDF format)
These Advanced Manual describe the details of the ID-51A/E features. This PDF formatted manual provides you
with convenient functions, as follows.
15
REPEATER AND DUPLEX OPERATIONS
15-4
Duplex operation
The Duplex operation shifts the transmit frequency
up or down from the receive frequency by an offset
amount.
D
Setting the frequency offset
q
Push [V/MHz]
to select the VFO mode.
w
Push [MENU]
.
e
Push D-pad(
) to select the root item (“DUP/
TONE...”), and then push D-pad(Ent).
D-pad
( )
(Ent)
r
Push D-pad(
) to select the “Offset Freq,” and then
push D-pad(Ent).
t
Rotate [DIAL] to set the frequency offset to be-
tween 0.000.00 and 59.99500 MHz, and then push
D-pad(Ent).
(Setting example: 1.000.00 MHz)
• The selected tuning step in the VFO mode is used when
setting the frequency offset.
• Pushing [V/MHz]
toggles the tuning digit, as shown
below.
TS*
1 MHz
10 MHz
* The frequency changes according to the preset tuning
steps. (p. 5-8)
y
Push [MENU]
to exit the [MENU] screen.
To reset to the default value.
Push [QUICK]
in step
t
as described above, then
push D-pad(Ent) to reset to the default value.
The current frequency
offset
Rotate [DIAL], then
push D-pad(Ent).
Push [QUICK]
Push D-pad(Ent)
[DIAL]
The current frequency
offset
NOTE:
• The frequency offset cannot be changed while using
the DR function.
•
-
cy offset. Depending on the frequency offset value,
the off band indication, “OFF,” appears on the display
when [PTT] is pushed. (p. 15-5)
Previous view
The Auto repeater function uses the preset frequen
Example: When the cursor is moved over
[V/MHz]
in the description, a
red circle appears around the ap-
propriate key(s).
(p. 15-5)
Move to the page, if clicked.
The screen shots at the right column, correspond
to the operating instructions and procedures
shows both setting and operating example.
15
REPEATER AND DUPLEX OPERATIONS
15-4
Duplex operation
The Duplex operation shifts the transmit frequency
up or down from the receive frequency by an offset
amount.
D
Setting the frequency offset
q
Push [V/MHz]
to select the VFO mode.
w
Push [MENU]
.
e
Push D-pad(
) to select the root item (“DUP/
TONE...”), and then push D-pad(Ent).
D-pad
( )
(Ent)
r
Push D-pad(
) to select the “Offset Freq,” and then
push D-pad(Ent).
t
Rotate [DIAL] to set the frequency offset to be-
tween 0.000.00 and 59.99500 MHz, and then push
D-pad(Ent).
(Setting example: 1.000.00 MHz)
• The selected tuning step in the VFO mode is used when
setting the frequency offset.
• Pushing [V/MHz]
toggles the tuning digit, as shown
below.
TS*
1 MHz
10 MHz
* The frequency changes according to the preset tuning
steps. (p. 5-8)
y
Push [MENU]
to exit the [MENU] screen.
To reset to the default value.
Push [QUICK]
in step
t
as described above, then
push D-pad(Ent) to reset to the default value.
The current frequency
offset
Rotate [DIAL], then
push D-pad(Ent).
Push [QUICK]
Push D-pad(Ent)
[DIAL]
The current frequency
offset
NOTE:
• The frequency offset cannot be changed while using
the DR function.
•
-
cy offset. Depending on the frequency offset value,
the off band indication, “OFF,” appears on the display
when [PTT] is pushed. (p. 15-5)
Previous view
The Auto repeater function uses the preset frequen
Shows a term description
When the mouse cursor is moved over a term which
is highlighted in yellow, the description of the term is
displayed.
15
REPEATER AND DUPLEX OPERATIONS
15-4
Duplex operation
The Duplex operation shifts the transmit frequency
up or down from the receive frequency by an offset
amount.
D
Setting the frequency offset
q
Push [V/MHz]
to select the VFO mode.
w
Push [MENU]
.
e
Push D-pad(
) to select the root item (“DUP/
TONE...”), and then push D-pad(Ent).
D-pad
( )
(Ent)
r
Push D-pad(
) to select the “Offset Freq,” and then
push D-pad(Ent).
t
Rotate [DIAL] to set the frequency offset to be-
tween 0.000.00 and 59.99500 MHz, and then push
D-pad(Ent).
(Setting example: 1.000.00 MHz)
• The selected tuning step in the VFO mode is used when
setting the frequency offset.
• Pushing [V/MHz]
toggles the tuning digit, as shown
below.
TS*
1 MHz
10 MHz
* The frequency changes according to the preset tuning
steps. (p. 5-8)
y
Push [MENU]
to exit the [MENU] screen.
To reset to the default value.
Push [QUICK]
in step
t
as described above, then
push D-pad(Ent) to reset to the default value.
The current frequency
offset
Rotate [DIAL], then
push D-pad(Ent).
Push [QUICK]
Push D-pad(Ent)
[DIAL]
The current frequency
offset
NOTE:
• The frequency offset cannot be changed while using
the DR function.
•
-
cy offset. Depending on the frequency offset value,
the off band indication, “OFF,” appears on the display
when [PTT] is pushed. (p. 15-5)
Previous view
The Auto repeater function uses the preset frequen
Move to the previously read page.
Click
Previous view
at the left top on an
each page, to move back to the previ-
ously read page.
Shows the location of keys
When the cursor is moved over a term with a red
underline, a red circle appears around the appro-
priate key(s) on the illustration of the transceiver.
15
REPEATER AND DUPLEX OPERATIONS
15-4
Duplex operation
The Duplex operation shifts the transmit frequency
up or down from the receive frequency by an offset
amount.
D
Setting the frequency offset
q
Push [V/MHz]
to select the VFO mode.
w
Push [MENU]
.
e
Push D-pad(
) to select the root item (“DUP/
TONE...”), and then push D-pad(Ent).
D-pad
( )
(Ent)
r
Push D-pad(
) to select the “Offset Freq,” and then
push D-pad(Ent).
t
Rotate [DIAL] to set the frequency offset to be-
tween 0.000.00 and 59.99500 MHz, and then push
D-pad(Ent).
(Setting example: 1.000.00 MHz)
• The selected tuning step in the VFO mode is used when
setting the frequency offset.
• Pushing [V/MHz]
toggles the tuning digit, as shown
below.
TS*
1 MHz
10 MHz
* The frequency changes according to the preset tuning
steps. (p. 5-8)
y
Push [MENU]
to exit the [MENU] screen.
To reset to the default value.
Push [QUICK]
in step
t
as described above, then
push D-pad(Ent) to reset to the default value.
The current frequency
offset
Rotate [DIAL], then
push D-pad(Ent).
Push [QUICK]
Push D-pad(Ent)
[DIAL]
The current frequency
offset
NOTE:
• The frequency offset cannot be changed while using
the DR function.
•
-
cy offset. Depending on the frequency offset value,
the off band indication, “OFF,” appears on the display
when [PTT] is pushed. (p. 15-5)
Previous view
The Auto repeater function uses the preset frequen
Previous view