A-6602H-2EX-
y
Printed in Japan
© 2007–2014 Icom Inc.
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
Printed on recycled paper with soy ink.
The IC-A210/IC-A210E mates with a Card edge connector
in the rack mount. Assemble the Card edge connector as
follows.
D
Card edge connector assembly
q
Strip 4 mm (0.16
″
) from each wire for the card edge
connector.
w
Tin the leads of the wires.
e
Pass the wires through a short length of 13 mm (0.5
″
)
heat shrink tubing.
r
Solder the leads to the contact terminals.
t
Cover the soldered terminals with the heat shrink tubing
and heat until they are fixed in place.
y
Cover the unused terminals with the heat shrink tubing
10 mm (0.4
″
), then heat them to prevent shorting.
D
Polarizing key
Before installing the Connector into the mounting bracket,
check the polarizing key position between contacts 8 and
9. Refer to Connector front view in
m
CONNECTOR IN-
FORMATION.
,
CARD EDGE CONNECTOR ASSEMBLY
Check the following points after transceiver installation.
- Polarity of the power supply.
-
NO
interference caused to other equipment.
-
NO
noise or interference from other equipment.
- VSWR is less than 2.5:1.
- Communication capability on both the highest and lowest
communication frequencies, if possible.
.
OPERATION CHECK
Connect the GPS receiver’s input/output terminals as below table.
INFORMATION FOR GPS RECEIVER CONNECTION
GPS receiver’s terminal
Connector
D-sub connector
Input terminal
pin 1
pin 3
Output terminal
pin 2
pin 10
L-type BNC
connector
(Purchase locally, if required)
Coaxial
connector
r
BNC-LP
r
BNC-LP
o
Nut
u
Antenna cable clip
i
Self-crimping nut
t
Washer
y
C-shaped ring
!2
Screws
!0
Screw
e
Screws Bind UNC
!5
Polarizing key
q
Mounting
bracket
w
Card edge connector
!1
Crimp nuts
q
Mounting
bracket
�
When using the MB-53
!8
Voltage sticker
(IC-A210E only)
MB-53
⁄0
MOUNTING BRACKET ASSEMBLY
D
Notes for making the mounting hole
The IC-A210/IC-A210E can be mounted securely in the
supplied mounting bracket.
Remember to allow adequate space for installation of cables
and connectors.
When installing 2 or more transceivers in a stack, the mount-
ing trays should be 1.3 mm
(0.05
″
)
apart.
The mounting bracket has 0.6 mm
(0.024
″
)
dimples in the
top, bottom, and both sides for proper spacing.
Mark and cut the mounting holes.
To support the mounting bracket, the rear mounting bosses
should be attached to the airframe.
⁄1
MARKING MOUNTING HOLES
D
Mounting bracket dimensions
160 mm; 6
5
⁄
16
″
33 mm; 1
5
⁄
16
″
260 mm; 10
1
⁄
4
″
D
Front panel dimensions
160 mm; 6
5
⁄
16
″
34 mm;
1
11
⁄
32
″
MEMO
DUAL
GRP
RCL
MEM
OFF
VOL
PUSH
TEST
COMM
DUAL EC
iA210
Allow space for the front panel as shown above (illustration: IC-A210).
D
Template
Cut out dimensions for the mounting bracket as follows.
160 mm; 6
5
⁄
16
″
33 mm;
1
5
⁄
16
″
D
Transceiver installation
q
Remove the front panel from the main unit, using a
3
⁄
32
″
allen wrench, then carefully disconnect the flat cable from
the front panel.
(Fig. 1)
w
Insert a
3
⁄
32
″
allen wrench into the hole of the main unit
and unscrew the inside lock screw until the in-side metal
catch touches the chassis hole.
(Fig. 2)
•
Use the metal catch located on bottom side of the transceiver
when installing into the existing mounting bracket with MB-113 .
Use when installing with
the original mounting bracket.
Main unit front view
Using this hole when
installing with the MB-113.
e
Rotate the lock screw clockwise 4 revolutions
(Fig. 3)
, and
then rotate counterclockwise a quarter revolution.
(Fig. 4)
r
Insert the main unit (transceiver) into the mounting
bracket.
(Fig. 5)
t
Screw the lock screw to fix the main unit (transceiver) to
the bracket.
(Fig. 6)
y
Connect the flat cable.
(Fig. 7)
u
Attach the front panel and re-screw the allen bolts
(Fig. 7)
.
D
Transceiver removal
The IC-A210/IC-A210E is easily removed from the mounting
bracket, if required.
q
Remove the front panel from the main unit, using a
3
⁄
32
″
allen wrench, then disconnect the flat cable from the front
panel.
w
Insert a
3
⁄
32
″
allen wrench into the hole of the main unit
and unscrew the inside lock screw.
e
Slowly pull the transceiver out from the mounting bracket.
r
Connect the flat cable to the front panel.
t
Attach the front panel and tighten the allen screws.
Fig. 1
Fig. 6
Fig. 5
Fig. 7
Fig. 1
Fig. 6
Fig. 5
Fig. 7
Clockwise: For installation.
Counterclockwise: For removal.
CAUTION:
Treat the flat cable with care
when disconnecting it.
CAUTION:
Treat the flat cable with care
when connecting it.
Clockwise: For installation.
Counterclockwise: For removal.
Surface
Flat cable
Fig. 2
Fig. 4
Fig. 3
Screw 4 revolutions
Unscrew a quarter
revolution
• Metal catch position
Good!
Bad
Metal catch
Surface
The flat cable
Fig. 2
Fig. 4
Fig. 3
Screw 4 revolutions
Unscrew a quarter
revolution
• Metal catch position
Metal catch
Flat cable
Good!
Bad
Flat cable
⁄2
MOUNTING TO THE BRACKET
CAUTION:
Tr e a t t h e f l a t c a bl e w i t h c a r e w h e n
disconnecting it to avoid possible damage.
Improper care disconnecting the cable can
cause damage and result in severe non-
warranty repair.
CAUTION:
Make sure that the flat cable between the
transceiver and front panel is securely
connected. The transceiver may not function
properly when loose or when a wrong
connection is made.
Improper care installing the cable can cause
damage and result in severe non-warranty
repair.
