![background image](http://html.mh-extra.com/html/icom/ic-f80ds/ic-f80ds_service-manual_612667010.webp)
4-3 PLL CIRCUITS
4-3-1 PLL CIRCUIT (MAIN UNIT)
The PLL circuit provides stable oscillation of the transmit
frequency and receive 1st LO frequency. The PLL circuit
compares the phase of the divided VCO frequency with the
reference frequency. The PLL output frequency is controlled
by the divided ratio (N-data) of the programmable divider.
The PLL circuit contains the two RX VCOs (Q600, D604,
D605 for 400–434 MHz, Q601, D606, D607 for 435–470
MHz) and one TX VCO (Q602, D608, D609). The oscillated
signal is amplified at the buffer amplifiers (Q605, Q606,
Q608) and applied to the PLL IC (IC1, pin 6) after being
passed through the LPF (L2, L3, C22, C25, C27, C28, C37).
The applied signal is divided at the prescaler and program-
mable divider section by the N-data ratio from the CPU
(IC307). The divided signal is phase-compared with the devided
reference frequency at the phase detector. The phase dif-
ference is output from pin 4 as a pulse signal after being
passed through the charge pump section. The output signal
is passed through the loop filter (R16, R17, C17, C24, C29,
C31) to converted into the DC voltage, and is then applied
to the VCO circuits as the lock voltage.
If the oscillated signal drifts, its phase changes from that of
the reference frequency, causing a lock voltage change to
compensate for the drift in the oscillated frequency.
4-3-2 VCO CIRCUITS (MAIN UNIT)
The VCO circuits contain separate two RX VCOs (Q600, D604,
D605 for 400–434 MHz, Q601, D606, D607 for 435–470
MHz) and one TX VCO (Q602, D608, D609). The oscillated
signal is amplified at the buffer amplifiers (Q605, Q606,
Q609) and is then applied to the TX/RX switch (D200,
D501). Then the receive 1st LO (RX) signal is applied to the
1st mixer (IC500, L503, L504, L506), and the transmit (TX)
signal is applied to the buffer amplifier (Q200).
A portion of the signal from the buffer amplifier (Q605,
Q606) is fed back to the PLL IC (IC1, pin 6) as the compari-
son signal via the buffer amplifier (Q608) and the LPF (L2,
L3, C22, C25, C27, C28, C37).
4 - 4
Loop
filter
PLST
SSO
SCK
4
Q601, D606, D607
RX VCO (435–470 MHz)
Q600, D604, D605
RX VCO (400–434 MHz)
TX VCO
Q602, D608, 609
6
10
14
15
16
PLL control signals from CPU (IC307)
15.3 MHz reference signal
from reference frequency osciilator (X1)
IC1 LMX2352TM
• PLL CIRCUIT
Shift register
Prescaler
Phase
detector
Divided
ratio
adjustment
Charge
pump
Programmable
divider
Reference
divider
Buffer
Q605,
Q606
Buffer
Q609
Buffer
Q608
to transmitter circuit
to 1st mixer circuit
D501
D200
LPF
LINE
DESCRIPTION
VCC
The voltage from the attached battery pack passed
through the power switch (Q309).
CPU5V
Common 5 V for the CPU (IC307) converted from the
VCC line at the CPU5V regulator (IC311).
5V
Common 5 V line converted from the VCC line at the
+5V regulator (Q307, Q308).
T5V
5 V for the transmit circuits regulated from the 5V line
by the T5V switch (Q305).
The switch is controlled by the "T5C" signal from the
CPU (IC307, pin 16).
S5V
5 V for the power save line regulated from the 5V line
by the S5V switch (Q304).
The switch is controlled by the "S5C" signal from the
CPU (IC307, pin 27).
R5V
5 V for the receive circuits regulated from the 5V line
by the R5V switch (Q306).
The regulator is controlled by the "R5C" signal from
the CPU (IC307, pin 26).
4-4 POWER SUPPLY CIRCUITS
4-4-1 VOLTAGE LINES (MAIN UNIT)
LINE
DESCRIPTION
DVDD3.3V
3.3 V for the CPU (IC12; DSP UNIT), DSP IC (IC7)
and EEPROM (IC17) regulated from the 5V line by the
+3VC regulator (IC1).
CVDD1.5V
1.5 V for the DSP IC (IC7) converted from the +5V
line at the +1.5VA regulator (IC2).
+3VD
3.3 V for the A/D converter (IC8) and LINER CODEC
IC (IC9) from the 5V line at the +3VD regulator (IC3).
4-4-2 VOLTAGE LINES (DSP UNIT)