PANEL DESCRIPTION
FUNCTION DISPLAY
BASIC OPERATION
CONNECTIONS
1
ICON AREA
Displays the icons, as shown below.
Displays the relative receive signal strength
level.
Displayed when the low output power is
selected.
Displayed when the Shift function is ON.
The user can use a Dealer Assignable key’s
secondary function in the Shift mode. Ask
your dealer for details.
Displayed when the channel is in the audible
(unmuted) mode.
Blinks after messages (Message or Status
Message) have been received.
Displayed when a matching signal is
received, depending on the presetting.
( For only the transceiver with the Bluetooth
function)
• Blinks when the Bluetooth function is ON.
• Displayed when the transceiver is paired
with a Bluetooth device.
• Blinks while scanning.
• Displayed when a scan is paused.
Displayed when the channel is selected as a
scan target channel.
• Displayed when the Encryption function
is ON.
• Blinks when decoding an encrypted
signal.
• Displayed when valid position data is
received.
• Blinks when searching for satellites.
Displayed when the Talk Around function is
ON.
Displayed when the Lone Worker function
is ON.
2
ALPHANUMERIC READOUT
Displays messages such as channel text.
3
DEALER ASSIGNABLE KEY ICONS
Displayed while the function assigned to [P1], [P2],
[P3], or [P4] is operating.
L
May not be displayed, depending on the assigned
function.
D
Microphone
D
Main unit
Microphone connector
Power key [ ]+ Power indicator
Status indicator:
Lights red:
Transmitting
Lights green: Receiving or squelch is open.
Status indicator
R
WARNING! NEVER
remove the fuse holders
from the DC power cable.
NOTE:
Use the terminals as
shown below for the cable
connections.
Crimp
Solder
Black
Red
Fuse holders
12 V
Battery
Antenna
Optional speaker
5
1
2
3
4
1
ANTENNA CONNECTOR
Connect an antenna. Contact your dealer about
antenna selection and placement.
2
ACC CABLE CONNECTOR
Attach an optional ACC cable to connect an external
device through D-Sub 15 pin or 25 pin cable. Contact
your dealer about the cable attachment.
3
EXTERNAL SPEAKER JACK
Connecta4~8Ωexternalspeaker.
4
MICROPHONE HANGER
The microphone ON/OFF hook function is usable
without the vehicle’s ground.
5
DC POWER CONNECTOR
Connect a 12 V DC battery. Pay attention to polarities.
6
IGNITION LEAD
Connects to an ignition line.
CAUTION:
DO NOT
connect to a 24 V battery. This
will damage the transceiver.
MOUNTING THE TRANSCEIVER
Mountthetransceiveronaflatsurfaceusingthemountingbracketsuppliedwithyourtransceiver.
1. Drill 4 holes on a flat surface where you want to install the mounting bracket.
L
When using the supplied nuts: Approximately 5.5 ~ 6 mm (d)
L
When using the supplied self-tapping screws: Approximately 2 ~ 3 mm (d)
2.
Attachthemountingbracketontheflatsurfaceusingthesuppliedscrews,nuts,andwashers.
3. Attach the transceiver to the mounting bracket using the supplied bracket bolts.
Mounting example:
Bracket bolt
(M4×8 mm)
Flat washer (M5)
Nut (M5)
[PTT]
[F1]*
Vol Up [+]*
Vol Down [–]*
Speaker
Ten-Keypad
[P3]*
[P1]*
[P2]*
[P4]*
[Up]/[Down]/
[Right]/[Left]*
[Emer]*
Power key [ ]
Microphone
Status
indicator
D
Turning ON the transceiver
z
Hold down [ ] for more than 2 seconds until the Status
indicator or Power indicator lights orange.
NOTE:
Entering the password may be required to turn ON
the transceiver, depending on the presetting.
Ask your dealer or the transceiver’s administrator for details.
D
Receiving
1. Push [Up] or [Down] to select a channel.
2. When a call is received, the Status indicator lights green.
L
Push [+] or [–] to adjust the audio output level to a
comfortable listening level.
D
Transmitting
CAUTION: DO NOT
transmit without an antenna.
1. Wait until the channel is clear to avoid interference.
2. While holding down [PTT], speak at your normal voice
level.
3. Release [PTT] to receive.
IMPORTANT:
Tomaximizethereadabilityofyoursignal:
1. After pushing [PTT], pause briefly before you start
speaking.
2. Hold the microphone 5 ~ 10 cm (2 ~ 4 inches) from
your mouth, then speak at your normal voice level.
* The assigned function may differ, depending on the presetting.
Ask your dealer or the transceiver’s administrator for details.
1
2
3
Screw
(4×16 mm)
Self-tapping
screws
(5×20 mm)
Spring washer (M5)
Mounting screws
(M5×12 mm)
Microphone connector:
PoE output voltage: 54 V
PoE output current: 0.6 A
Power indicator:
Lights orange:
Power ON
Lights green:
Connected with the microphone.
Lights red:
Disconnected from the microphone.
Status indicator:
Lights red:
Transmitting
Lights green:
Receiving or squelch is open.
6
