![background image](http://html1.mh-extra.com/html/icom/ic-f31gs/ic-f31gs_servise-manual_4243052011.webp)
5 - 1
5-1 PREPARATION
When you adjust the contents on pages 5-5 and 5-6, SOFTWARE ADJUSTMENT, the optional CS-F30G ADJ
ADJUSTMENT SOFT-
WARE
(Rev. 1.0 or later), *OPC-966
JIG CABLE
(modified OPC-966
CLONING CABLE
) are required.
■
REQUIRED TEST EQUIPMENT
SECTION 5 ADJUSTMENT PROCEDURES
■
SYSTEM REQUIREMENTS
• IBM PC compatible computer with an RS -232C serial port
(38400 bps or faster).
• Microsoft Windows 95 or Windows 98
• Intel i486DX processor or faster (Pentium 100 MHz or
faster recommended)
• At least 16 MB RAM and 10 MB of hard disk space
• 640
×
480 pixel display (800
×
600 pixel display recommend-
ed)
■
ADJUSTMENT SOFTWARE INSTALLATION
q
Boot up Windows.
- Quit all applications when Windows is running.
w
Insert the ‘CS-F30G’ into the appropriate drive.
e
Select ‘Run’ from the [Start] menu.
r
Type the setup program name using the full path name,
then push [Enter] key.
(ex. D:\CSF30GADJ\disk1\Setup.exe)
t
Follow the prompts.
y
Program group ‘CS-F30G ADJ’ appears in the ‘Programs’
folder of the [Start] menu.
■
STARTING SOFTWARE ADJUSTMENT
q
Connect IC-F30GT, F30GS, F31GT or F31GS and PC
with *OPC-966
JIG CABLE
.
w
Turn the transceiver power ON.
e
Boot up Windows, and click the program group ‘CS-F30G
ADJ’ in the ‘Programs’ folder of the [Start] menu, then
CS-F30G ADJ’s window appears.
r
Click ‘Connect’ on the CS-F30G’s window, then appears
IC-F30GT, F30GS, F31GT or F31GS’s up-to-date condi-
tion.
t
Set or modify adjustment data as desired.
IBM is a registered trademark of International Bussiness
Machines Corporation in the U.S.A. and other countries.
Microsoft and Windows are registered trademarks of
Microsoft Corporation in the U.S.A. and other countries.
Screen shots produced with permission from Microsoft
Corporation. All other products or brands are registered
trademarks or trademarks of their respective holders.
• High power transmittion
When you adjust the output power (high power), the battery
type detector must be connected to GND (see illustration at
below). Otherwise the transceiver does not transmit high
power, the output power will be low.
EQUIPMENT
DC power supply
FM deviation meter
Frequency counter
Digital multimeter
RF power meter
(terminated type)
GRADE AND RANGE
Output voltage
: 7.5 V DC
Current capacity
: 5 A or more
Frequency range
: DC–300 MHz
Measuring range
: 0 to ±10 kHz
Frequency range
: 0.1–300 MHz
Frequency accuracy : ±1 ppm or better
Sensitivity
: 100 mV or better
Input impedance
: 10 M
Ω
/V DC or better
Measuring range
: 1–10 W
Frequency range
: 100–300 MHz
Impedance
: 50
Ω
SWR
: Less than 1.2 : 1
EQUIPMENT
Audio generator
Attenuator
Standard signal
generator (SSG)
DC voltmeter
Oscilloscope
AC millivoltmeter
GRADE AND RANGE
Frequency range
: 300–3000 Hz
Output level
: 1–500 mV
Power attenuation
: 40 or 50 dB
Capacity
: 10 W or more
Frequency range
: 100–300 MHz
Output level
: 0.1 µV–32 mV
(–127 to –17 dBm)
Input impedance
: 50 k
Ω
/V DC or better
Frequency range
: DC–20 MHz
Measuring range
: 0.01–20 V
Measuring range
: 10 mV–10 V
Battery type detector
+
–
DC power supply
7.5 V/5.0 A
Battery type detector
Connect to GND
Summary of Contents for IC-F31GS
Page 1: ...VHF TRANSCEIVER iC f30gt iC f30gs iC f3 1 gt iC f3 1 gs...
Page 2: ......
Page 36: ......