background image

F C C   s tAt e M e N t

This equipment has been tested and found to comply with the limits for a Class b digital device, 
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection 
against harmful interference in a residential installation. This equipment generates, uses and can 
radiate radio frequency energy and, if not installed and used in accordance with the instructions, 
may cause harmful interference to radio communications. However, there is no guarantee that 
interference will not occur in a particular installation. If this equipment does cause harmful 
interference to radio or television reception, which can be determined by turning the equipment 
off and on, the user is encouraged to try to correct the  
interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that  

 

to which the receiver is connected. 

Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the  
following two conditions:

1) 

This device may not cause harmful interference.

2) 

This device must accept any interference received, including  

 

interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance 
could void the user’s authority to operate the equipment.

F C C   r F   r A d I At I o N   e x p o s U r e   s tAt e M e N t:

This device has been tested for compliance with FCC RF Exposure (SAR) limits in the typical 
laptop computer configuration and this device can be used in desktop or laptop computers. 
This device cannot be used with handheld PDAs (personal digital assistants). This device and its 
antenna must not be co-located or operated in conjunction with any other antenna or transmitter. 
SAR measurements are based on a 5mm spacing from the body and that compliance is achieved 
at that distance.

Summary of Contents for NI-707547












Reviews: