background image

ICE TECH SS / SK                                                                                                                      Technical Service 
Manual

 

 

 

24 

                                                                                                                                                                                                              

 

16) Allow machine to make ice for at least 15 minutes. 

WARNING:** Discard ice produced during cleaning procedure. 

17) Disconnect unit, place cover and check for water leaks.  

18) Change joint in water plug if necessary. 

19) Replace filters if necessary. (Machines provided with 5mm filters). 

20) Reconnect machine. 

Cleaning the ice bin 

1) Unplug the machine, turn off water supply, and empty storage bin of ice 

2) Wipe with a kitchen cloth soaked in bleach and detergent 

3) If white lime stains do not vanish, rub with some lemon or vinegar, wait for a few minutes and 

wipe with the cloth again. 

4) Rinse with plenty of water, dry, and run the machine 

Cleaning the outside of the machine  

Follow the same procedure as for the ice bin. 

Spray nozzles and connecting pipes 

1) Remove the curtain (it can be cleaned with vinegar or phosphoric acid, rinse, clean with bleach, 

rinse) 

2) Remove the metal grill and clean likewise 

3) Pull the connecting pipe upwards with some force. 

4) Remove the spray nozzles by pulling them out one by one from the square pipe, and remove 

the pipe ends. Clean everything 

5) Pull out the round wire mesh filter with some force. 

6) Put everything back together again. 

ATTENTION; 

IT 

IS 

ESSENTIAL 

THAT 

SPRAY 

NOZZLES 

ARE 

COMPLETELY 

PERPENDICULAR, OTHERWISE SOME CUBES MAY NOT BE FORMED WELL. 

7) Place the grill over the nozzles, with the back spots secure. 

8) Install the curtain, ensuring that all of the strips can move freely. 

9) Run the machine but discard the first set of ice cubes. 

Cleaning the water inlet filters 

Summary of Contents for SS 25





























Reviews: